文献速递创伤骨科手外科与足踝外科

掌骨位置与月骨面螺钉固定对背侧腕跨接桥接钢板治疗关节内桡骨远端骨折的生物力学分析

Metacarpal Position and Lunate Facet Screw Fixation in Dorsal Wrist-Spanning Bridge Plates for Intra-Articular Distal Radial Fracture: A Biomechanical Analysis.
PubMed 文献 · J Bone Joint Surg Am · 2020-01-01

这项生物力学研究在14对尸体配对标本(28例腕)中模拟关节内桡骨远端骨折,比较背侧腕跨接钢板固定于第二或第三掌骨时月骨面骨折块的位移,并评估附加月骨面锁定螺钉的刚度。结果显示固定于第三掌骨在各轴向载荷下均更有效抵抗位移,附加螺钉在≥200 N载荷下进一步增加刚度,300 N时平均位移均<1 mm。

要点

  • 固定于第三掌骨较第二掌骨在各轴向载荷下均更有效抵抗月骨面骨折块位移(p<0.008)。
  • 附加月骨面骨折块内锁定螺钉在≥200 N载荷下进一步增加构造刚度(p<0.008)。
  • 300 N载荷下各组平均位移均<1 mm,第三掌骨加螺钉组为0.2 mm。

核心结论

  • 背侧腕跨接钢板固定于第三掌骨并附加骨折块内螺钉是最具生物力学优势的构造,但其他因素可能支持选择替代的远端固定位置。

研究设计与样本

  • 尸体配对研究,样本量14对配对标本(28例腕)计算可达到81.7%检验效能。
  • 28例肢体随机分配至背侧腕跨接钢板固定于第二掌骨(组1)或第三掌骨(组2),每例腕行截骨模拟不稳定关节内桡骨远端骨折。
  • 在50、100、150、200、250、300 N轴向载荷下使用差分可变磁阻传感器测量月骨面骨折块相对于干骺端骨折块的位移。
  • 初始测试后在第三掌骨组(组3)经钢板置入锁定螺钉至月骨面骨折块,并在所有载荷下重复位移测量。
  • 采用配对双尾t检验及Bonferroni校正(显著性p<0.008)评估组间骨折块稳定性差异。

主要发现

  • 300 N时平均骨折位移组1为0.8 mm、组2为0.4 mm、组3为0.2 mm。
  • 在所有轴向载荷下,固定于第三掌骨较第二掌骨更有效抵抗位移(p<0.008)。
  • 附加月骨面螺钉在≥200 N载荷下进一步增加构造刚度(p<0.008)。
  • 所有组在300 N载荷下月骨面骨折块平均位移均<1 mm。

临床怎么用

  • 对于关节内桡骨远端骨折,背侧腕跨接钢板固定于第三掌骨并附加骨折块内螺钉可提供最有效的月骨面骨折块稳定。
  • 本研究验证了在背侧腕跨接钢板固定中使用骨折块内螺钉以增加稳定性。

以上解读依据论文摘要(全文未开放获取或许可不允许翻译转载)。

原文

BACKGROUND: A dorsal wrist-spanning plate (DWSP) can be affixed to the second or third metacarpal, depending on the morphology of the distal radial fracture (DRF) and on surgeon preference, but comparative biomechanical analyses between these methods are limited. This biomechanical study compared fixation to the second metacarpal versus the third metacarpal as measured by lunate facet fragment displacement in a cadaveric model of an axially loaded intra-articular DRF. The construct rigidity with the addition of an intrafragmentary lunate facet locking screw was also evaluated. METHODS: A sample size of 14 cadaveric matched pairs was calculated to achieve 81.7% power. The 28 limbs were randomized to DWSP fixation to the second metacarpal (Group 1) or third metacarpal (Group 2); each wrist underwent an osteotomy simulating an unstable intra-articular DRF. Limbs were tested at axial loads of 50, 100, 150, 200, 250, and 300 N. Lunate facet displacement from the metaphyseal fragment at each load was measured with use of differential variable reluctance transducers. After initial testing, a locking screw was placed through the plate into the lunate facet fragment in the third metacarpal group (Group 3). Displacement measurements were repeated for all loads. Paired 2-tailed t tests with Bonferroni correction (significance, p < 0.008) were performed to assess differences in fragment stability between groups. RESULTS: The average fracture displacement at 300 N was 0.8 mm in Group 1, 0.4 mm in Group 2, and 0.2 mm in Group 3. Plating to the third metacarpal more effectively resisted displacement compared with the second metacarpal at all axial loads (p < 0.008). The addition of a lunate facet screw further stiffened the construct at loads of ≥200 N (p < 0.008). CONCLUSIONS: Plate fixation to the third metacarpal with an intrafragmentary screw was the most biomechanically favorable construct, although other factors may favor an alternative distal fixation site. Mean displacement of the lunate facet fragment at 300 N was <1 mm in all groups. CLINICAL RELEVANCE: The present study demonstrated that a DWSP affixed to the third metacarpal with an intrafragmentary screw provides the most effective stabilization of the lunate facet fragment in intra-articular DRFs. This study validates the use of intrafragmentary screws to increase stability in DWSP fixation.

来源:J Bone Joint Surg Am,查看原文。版权归原作者所有。

引用

  1. Guerrero EM, Lauder A, Federer AE, et al. Metacarpal Position and Lunate Facet Screw Fixation in Dorsal Wrist-Spanning Bridge Plates for Intra-Articular Distal Radial Fracture: A Biomechanical Analysis. J Bone Joint Surg Am. 2020. PMID: 31904607. doi:10.2106/JBJS.19.00769

供执业医师工作参考,不替代临床判断;数值与分级以指南原文为准。