3D打印钛假体重建枢椎:连续三例的技术与结局
本文报告连续三例因肿瘤破坏或类风湿关节炎导致枢椎结构受损的患者,采用患者特异性3D打印钛假体进行重建。三例均获得成功的手术结局与症状缓解,无显著并发症,随访至术后14个月临床与影像学结果良好。证据等级为4级。
要点
- 3D打印定制钛假体可用于枢椎前柱重建,三例均手术成功且无显著并发症。
- 适应证包括甲状腺髓样癌转移、多发性骨髓瘤及类风湿关节炎所致枢椎破坏。
- 术后随访至14个月,临床与影像学均显示良好结局。
核心结论
- 患者特异性3D打印钛假体用于枢椎前柱重建在连续三例中均获得成功,手术结局与症状缓解良好且无显著并发症。
- 作者认为这些病例为定制假体用于复杂脊柱手术的新兴文献增添了证据。
研究设计与样本
- 本研究为病例系列,共纳入3例在本中心接受患者特异性3D打印钛假体重建结构受损枢椎的患者。
- 研究描述了手术与假体设计方法,并评估其结局,证据等级为4级。
主要发现
- 两例枢椎破坏源于肿瘤:一例为甲状腺髓样癌转移,另一例为多发性骨髓瘤。
- 第三例枢椎受损为类风湿关节炎的并发症。
- 所有患者均获得成功的手术结局与症状缓解,无显著并发症。
- 临床与影像学随访至术后14个月,所有病例均显示良好结局。
临床怎么用
- 对于枢椎结构受损的选定病例,可考虑采用患者特异性3D打印钛假体行前柱重建。
- 术后需结合临床与影像学随访评估重建效果与并发症。
局限性
- 本文为仅含3例的病例系列,证据等级为4级,样本量小且随访时间有限。
以上解读依据论文摘要(全文未开放获取或许可不允许翻译转载)。
原文
STUDY DESIGN: Three patients were treated at our center with patient-specific three-dimensional (3D)-printed titanium prostheses for the reconstruction of structurally compromised C2 vertebrae. OBJECTIVE: To describe our surgical and device design approach to these clinical scenarios and evaluate their outcomes. SUMMARY OF BACKGROUND DATA: There are a limited but increasing number of case reports and series describing the use of 3D-printed prostheses for high cervical surgery. METHODS: We have collated and reviewed three cases using patient-specific 3D-printed prostheses. RESULTS: We report two cases arising from neoplastic destruction; one resulting from metastatic medullary thyroid carcinoma, and the other from multiple myeloma. We additionally describe a case of C2 compromise as a complication of rheumatoid arthritis. All patients included in this report achieved successful surgical outcomes and symptom relief without significant complication. Clinical and radiological follow-up has demonstrated good outcomes in all cases up to 14-months postprocedure. CONCLUSIONS: These cases describe successful use of custom 3D-printed prostheses for reconstruction of the anterior vertebral column through C2, and add to the emerging body of literature detailing the use of custom prostheses for complex spinal surgery. LEVEL OF EVIDENCE: 4.
引用
- Hunn SAM, Koefman AJ, Hunn AWM, et al. 3D-printed Titanium Prosthetic Reconstruction of the C2 Vertebra: Techniques and Outcomes of Three Consecutive Cases. Spine (Phila Pa 1976). 2020. PMID: 31809469. doi:10.1097/BRS.0000000000003360
供执业医师工作参考,不替代临床判断;数值与分级以指南原文为准。