文献速递关节外科

全膝关节置换术中胫骨截骨面有多平?

How Flat Is the Tibial Osteotomy in Total Knee Arthroplasty?
PubMed 文献 · J Arthroplasty · 2019-10-09

本研究对14例尸体膝关节使用标准器械进行无骨水泥全膝置换,激光扫描截骨面并植入胫骨托,通过组织切片观察骨-托接触情况;发现初始平整度平均1.1±0.35mm,冲击后79.4%±0.3%表面有骨接触,非接触区多位于中央,且平整度与接触面积呈负相关(R²=0.605)。

要点

  • 胫骨截骨面平整度与骨-托接触面积呈负相关(R²=0.605)。
  • 冲击植入过程使截骨面凸起变平,从而产生大部分接触。
  • 非接触间隙多位于截骨面中央、靠近髓腔区域。

核心结论

  • 胫骨截骨面平整度与骨-胫骨托接触面积百分比呈负相关。
  • 几乎所有的托-胫骨接触是在植入过程中通过压平胫骨表面凸起产生的。
  • 托与胫骨之间的间隙一致位于截骨面中央、靠近髓腔的区域。

研究设计与样本

  • 八名外科医生使用标准器械准备14例尸体膝关节进行无骨水泥全膝置换。
  • 用激光扫描仪捕获每个截骨面的形貌并生成三维计算机模型。
  • 植入无骨水泥胫骨托后,将胫骨解剖、包埋于树脂中切片,在立体显微镜下观察骨-托接触点并整合至三维模型生成接触图。

主要发现

  • 所有标本的平均初始平整度为1.1±0.35mm。
  • 冲击后,79.4%±0.3%的表面建立了骨接触。
  • 非接触区域中17.6%在距托0.3mm以内。
  • 仅2.6%的表面距离被认为妨碍骨长入。
  • 非接触区域通常位于中央。

以上解读依据论文摘要(全文未开放获取或许可不允许翻译转载)。

原文

BACKGROUND: Cementless total knee arthroplasty has been developed to decrease the incidence of failure in younger and more active patients. However, failures are still more common in cementless versus cemented components. It is hypothesized that this is triggered by incomplete bone-tray contact. The present study compares the final contact area of a cementless tray as a function of the initial osteotomy flatness. METHODS: Eight surgeons prepared 14 cadaveric knees for cementless total knee replacement using standard instrumentation. The topography of each osteotomy was captured with a laser scanner; 3-dimensional computer models of the surfaces were generated. After scanning each tibia, the surgeons implanted cementless tibial trays using a manual impactor. Each tibia was then dissected, embedded in mounting resin, and sectioned. The sectioned blocks were observed under stereomicroscopy to identify points of bone-tray contact which were incorporated into the 3-dimensional models. Maps were then generated illustrating depicting contacting and noncontacting areas. RESULTS: The mean initial flatness of all specimens was 1.1 ± 0.35 mm. After impaction, 79.4% ± 0.3% of the surface had established bony contact. Of the noncontacting areas, 17.6% were within 0.3 mm of the tray. Only 2.6% of the surface was at distances reported to impede ingrowth. Noncontacting areas were typically located centrally. A trend in decreasing percent contact area with increased flatness tolerance was observed (R2 = 0.605). CONCLUSION: (1) There is an inverse correlation between the flatness of the tibial osteotomy and the percentage of the bony surface in contact with underside of the tibial tray. (2) Almost all tray-tibia contact is generated during implantation through flattening of elevated features on the tibial surface. (3) Gaps between the tray and the tibia are consistently located in the central regions of the osteotomy proximal to the medullary canal.

来源:J Arthroplasty,查看原文。版权归原作者所有。

引用

  1. Delgadillo LE, Jones HL, Ismaily SK, et al. How Flat Is the Tibial Osteotomy in Total Knee Arthroplasty? J Arthroplasty. 2019. PMID: 31694778. doi:10.1016/j.arth.2019.10.007

供执业医师工作参考,不替代临床判断;数值与分级以指南原文为准。