文献速递关节外科

一次性3D打印器械用于全膝关节置换术的可行性

Feasibility of single-use 3D-printed instruments for total knee arthroplasty.
PubMed 文献 · Bone Joint J · 2019-01-01

本研究评估设计与引入通用3D打印器械用于全膝关节置换术常规使用的可行性,器械设计为预组装以理论上减少手术时间与技能要求,并限制截骨角度与距离于安全区内以兼顾机械或解剖对线目标。测试显示丙烯腈丁二烯苯乙烯在蒸汽灭菌前后尺寸变化,振荡锯测试中尼龙12和聚甲基丙烯酸甲酯(MED610)产生碎屑、断裂或进一步尺寸变化,而聚醚酰亚胺ULTEM 1010受影响最小。结论认为3D打印器械技术可行并具一定优势,但所有手术步骤能否由一套器械完成、配送物流及经济性等因素需进一步研究。

要点

  • 丙烯腈丁二烯苯乙烯经蒸汽灭菌后发生尺寸变化。
  • 尼龙12和MED610在振荡锯测试中产生碎屑、断裂或尺寸变化。
  • 聚醚酰亚胺ULTEM 1010在振荡锯测试中受影响最小。

核心结论

  • 研究表明3D打印器械技术可行并具一定优势,但所有手术步骤能否由一套3D打印器械完成、配送物流及经济性等因素需进一步研究。

研究设计与样本

  • 设计利用3D打印技术的器械,所有部件预组装,理论上减少手术时间与技能要求。
  • 器械功能上限制截骨角度与距离于安全区内,同时兼顾机械或解剖对线目标。
  • 设计并生产典型器械形状及配合部件(如燕尾榫和螺钉),以确定最合适的生物相容材料。

主要发现

  • 蒸汽灭菌前后尺寸分析显示丙烯腈丁二烯苯乙烯无法承受温度而不发生尺寸变化。
  • 带槽切割块的振荡锯测试中,尼龙12和聚甲基丙烯酸甲酯(MED610)产生碎屑、断裂或进一步形状尺寸变化。
  • 振荡锯测试中聚醚酰亚胺ULTEM 1010受影响最小。

临床怎么用

  • 原文未据此给出推荐。

局限性

  • 所有手术步骤能否由一套3D打印器械完成需进一步研究。
  • 配送物流需进一步研究。
  • 经济性方面需进一步研究。

以上解读依据论文摘要(全文未开放获取或许可不允许翻译转载)。

原文

AIMS: This aim of this study was to assess the feasibility of designing and introducing generic 3D-printed instrumentation for routine use in total knee arthroplasty. MATERIALS AND METHODS: Instruments were designed to take advantage of 3D-printing technology, particularly ensuring that all parts were pre-assembled, to theoretically reduce the time and skill required during surgery. Concerning functionality, ranges of resection angle and distance were restricted within a safe zone, while accommodating either mechanical or anatomical alignment goals. To identify the most suitable biocompatible materials, typical instrument shapes and mating parts, such as dovetails and screws, were designed and produced. RESULTS: Before and after steam sterilization, dimensional analysis showed that acrylonitrile butadiene styrene could not withstand the temperatures without dimensional changes. Oscillating saw tests with slotted cutting blocks produced debris, fractures, or further dimensional changes in the shape of Nylon-12 and polymethylmethacrylate (MED610), but polyetherimide ULTEM 1010 was least affected. CONCLUSION: The study showed that 3D-printed instrumentation was technically feasible and had some advantages. However, other factors, such as whether all procedural steps can be accomplished with a set of 3D-printed instruments, the logistics of delivery, and the economic aspects, require further study. Cite this article: Bone Joint J 2019;101-B(7 Supple C):115-120.

来源:Bone Joint J,查看原文。版权归原作者所有。

引用

  1. Hooper J, Schwarzkopf R, Fernandez E, et al. Feasibility of single-use 3D-printed instruments for total knee arthroplasty. Bone Joint J. 2019. PMID: 31256657. doi:10.1302/0301-620X.101B7.BJJ-2018-1506.R1

供执业医师工作参考,不替代临床判断;数值与分级以指南原文为准。