文献速递关节外科

提高胫骨托-骨水泥界面初始结合强度的技术

Techniques for improving the initial strength of the tibial tray-cement interface bond.
PubMed 文献 · Bone Joint J · 2019-01-01

本研究将48个胫骨托用两种骨水泥固定于丙烯酸树脂基座,测试骨水泥固化时间(早、正常、晚)、涂覆部位(仅平台或平台加龙骨)及骨髓脂肪污染对界面推出强度的影响。结果显示早期涂覆、涂覆龙骨及避免污染可提高界面强度,脂肪污染金属/骨水泥界面使强度降低99%和94%。

要点

  • 早期涂覆骨水泥较正常时间使Simplex和Palacos骨水泥界面平均强度分别提高48%和72%。
  • 涂覆龙骨较仅涂覆平台使两种骨水泥界面平均强度分别提高153%和147%。
  • 金属/骨水泥界面脂肪污染使平均强度分别降低99%和94%,预先在胫骨托底面加骨水泥后降低幅度减小至65%和43%。

核心结论

  • 为最大化胫骨托/骨水泥界面强度,应在骨水泥混合后尽快涂覆于假体、避免界面污染,并同时涂覆龙骨和平台。

研究设计与样本

  • 体外实验研究,共48个胫骨托用两种厂商骨水泥固定于丙烯酸树脂基座,采用推出试验连续记录载荷。

主要发现

  • 与正常时间相比,早期涂覆骨水泥使Simplex和Palacos骨水泥的界面平均强度分别提高48%和72%。
  • 与正常时间相比,晚期涂覆骨水泥使Simplex和Palacos骨水泥的界面平均强度分别降低47%和73%。
  • 涂覆龙骨使Simplex和Palacos骨水泥的界面平均强度分别提高153%和147%。
  • 金属/骨水泥界面脂肪污染使Simplex和Palacos骨水泥的界面平均强度分别降低99%和94%;预先在胫骨托底面加骨水泥后,平均强度仅分别降低65%和43%。

临床怎么用

  • 作者结论认为,为最大化胫骨托/骨水泥界面强度,应在骨水泥混合后尽快涂覆于假体、避免界面污染,并同时涂覆龙骨和平台。

局限性

  • 原文未报告局限性。

以上解读依据论文摘要(全文未开放获取或许可不允许翻译转载)。

原文

AIMS: Loosening of the tibial component after total knee arthroplasty (TKA) is a common indication for revision. Increasing the strength of the initial tibial implant/cement interface is desirable. There is little information about the surgical techniques that lead to the highest strength. We investigated the effects of eight variables on the strength of the initial tibial baseplate/cement interface. MATERIALS AND METHODS: A total of 48 tibial trays were cemented into acrylic holders using cement from two manufacturers, at three different times (early, normal, and late) using two techniques: cementing the tibial plateau or the plateau and the keel; and involving two conditions of contamination with marrow fat (at the metal/cement and cement/cement interfaces). Push-out tests were performed with load continuously recorded. RESULTS: Compared with normal conditions, early cementing increased the mean strength of the interface when using the two cements, Simplex and Palacos, by 48% and 72%, respectively. Late cementing reduced the strength by 47% and 73%, respectively. Cementing the keel increased the mean strength by 153% and 147%, respectively, for the two cements. Contamination of the metal/cement interface with fat reduced the mean strength by 99% and 94% for the two cements but adding cement to the underside of the tibial tray prior to insertion resulted in the mean strength being lowered by only 65% and 43%, respectively. CONCLUSION: In order to maximize the strength of the tibial tray/cement interface, cement should be applied to the component soon after mixing, contamination of the interface should be avoided, and the keel and the plateau should be cemented.

来源:Bone Joint J,查看原文。版权归原作者所有。

引用

  1. Billi F, Kavanaugh A, Schmalzried H, et al. Techniques for improving the initial strength of the tibial tray-cement interface bond. Bone Joint J. 2019. PMID: 30648489. doi:10.1302/0301-620X.101B1.BJJ-2018-0500.R1

供执业医师工作参考,不替代临床判断;数值与分级以指南原文为准。