髋臼杯位置与部件设计对髋关节动态脱位的影响
该体外研究使用材料测试系统比较半球形、金属对金属和双动性(DM)三种设计在不同髋臼外倾角、前倾角和骨盆倾斜下的动态脱位距离与脱位力。结果显示DM髋在几乎所有测试角度下动态脱位距离均大于其他设计(60°外倾/0°前倾除外),作者认为若术前或术中担心不稳,使用DM植入物可增加动态脱位距离。
要点
- DM设计在所有测试的外倾角、前倾角和骨盆倾斜角下动态脱位距离均大于其他设计,但60°外倾/0°前倾除外。
- 骨盆倾斜26°时,脱位距离随前倾角增大而增加,随外倾角增大而减小。
- 作者认为若术前或术中担心不稳,使用DM植入物可增加动态脱位距离。
核心结论
- 临床结果已显示DM设计可能减少脱位,这些数据支持该发现,并提示若术前或术中担心不稳,使用DM植入物可增加动态脱位距离。
研究设计与样本
- 该动态脱位距离模型使用材料测试系统,设定髋臼部件外倾角(30°、45°和60°)、前倾角(0°、15°和30°)和骨盆倾斜(5°[站立]和26°[坐起])。
- 测试组包括带模块化聚乙烯内衬和32 mm头的半球形杯、带40 mm钴铬(CoCr)头的金属对金属髋表面置换杯设计,以及外径42 mm活动内衬、内层28 mm活动头的DM设计。
主要发现
- DM髋的动态脱位距离在所有测试的外倾角、前倾角和骨盆倾斜角下均大于其他设计,但60°外倾/0°前倾除外。
- 在骨盆倾斜26°时,观察到脱位距离随前倾角增大而增加,随外倾角增大而减小。
临床怎么用
- 作者认为,若术前或术中担心不稳,使用DM植入物可增加动态脱位距离。
局限性
- 原文未报告局限性。
以上解读依据论文摘要(全文未开放获取或许可不允许翻译转载)。
原文
BACKGROUND: Dislocation is a major complication following total hip arthroplasty, with risk factors such as surgical technique, implant positioning, and implant design. Literature has suggested the distance the femoral head must travel before dislocation to be a predictive factor of dislocation where smaller travel distance has increased dislocation risk. The purpose of this study was to compare 3 designs (hemispherical, metal-on-metal, and dual mobility [DM]) in terms of the dynamic dislocation distance and force required to dislocate. METHODS: This dynamic dislocation distance model used a material testing system that defined acetabular component inclination (30°, 45°, and 60°), anteversion angles (0°, 15°, and 30°), and pelvic tilt (5° [standing] and 26° [chair rise]). Testing groups included a hemispherical shell with a modular polyethylene liner and 32-mm head, a metal-on-metal hip resurfacing cup design with a 40-mm CoCr head, and a DM design with a 42-mm outside diameter articulating liner and an inner 28-mm articulating head. RESULTS: The dynamic dislocation distance of the DM hip was greater than that of the other designs for all inclination, anteversion, and pelvic tilt angles tested with the exception of 60° inclination/0° anteversion. At 26° pelvic tilt, it was observed that dislocation distance increased with greater anteversion and decreased with larger inclination. CONCLUSION: Clinical results have shown the DM design may reduce dislocation. These data support those findings and suggest that if instability is a concern preoperatively or intraoperatively, using a DM implant increases the dynamic dislocation distance.
引用
- Higuera Rueda CA, Ferguson DF, Scholl L, et al. Influence of Acetabular Shell Position and Component Design on Hip Dynamic Dislocation. J Arthroplasty. 2018. PMID: 30639282. doi:10.1016/j.arth.2018.12.012
供执业医师工作参考,不替代临床判断;数值与分级以指南原文为准。