全髋关节置换术中头部锥度腐蚀导致头部触底及随后的严重股骨柄锥度失效
本研究分析取出的钴铬合金股骨头(n=30,LFIT;Stryker)和Ti-12Mo-6Zr-2Fe(TMZF)股骨柄(n=10,Accolade I;Stryker),发现头部锥度材料丢失随在位时间增加至20.8 mm³(P < .001),平均线性材料丢失超过76 μm可导致触底(12个头部观察到),有限元模型显示11/13 TMZF锥度变形和微动显著增大。作者认为11/13 TMZF锥度配36 mm头径的腐蚀风险高于更大锥度和更硬材料,该组合的失效不限于召回的头尺寸,对此植入组合的患者应密切监测。
要点
- 头部锥度材料丢失随在位时间增加,可达20.8 mm³(P < .001)。
- 头部锥度平均线性材料丢失超过76 μm可导致触底,12个头部观察到该现象。
- 11/13 TMZF锥度配36 mm头径的腐蚀风险高于更大锥度和更硬材料,失效不限于召回头尺寸。
核心结论
- 11/13 TMZF锥度设计配36 mm头径的腐蚀风险高于更大锥度和更硬材料制成的锥度。
- 该组合的失效不限于召回所包含的头尺寸。
- 作者建议对此植入组合的患者进行密切监测。
研究设计与样本
- 研究分析取出的钴铬合金股骨头(n=30,LFIT;Stryker,马瓦,新泽西州)和Ti-12Mo-6Zr-2Fe(TMZF)股骨柄(n=10,Accolade I;Stryker)。
- 采用三维坐标测量和扫描确定锥度材料丢失,并通过分析确定头与柄之间的初始尖端间隙。
- 使用有限元模型研究锥度材料和锥度尺寸对锥度变形和微动的影响。
主要发现
- 头部锥度材料丢失随在位时间增加,体积达20.8 mm³(P < .001)。
- 头部锥度平均线性材料丢失超过76 μm经分析确认可导致触底,在12个头部中观察到。
- 有限元计算显示,小尺寸11/13 TMZF锥度相比其他材料和锥度设计具有显著更大的变形和微动,且微动模式明显不同。
关键数值与推荐
- 头部锥度材料丢失体积达20.8 mm³(P < .001)。
- 头部锥度平均线性材料丢失超过76 μm可导致触底,12个头部观察到。
临床怎么用
- 作者认为,对使用该植入组合的患者应密切监测。
- 原文未据此给出其他推荐。
局限性
- 原文未报告局限性。
以上解读依据论文摘要(全文未开放获取或许可不允许翻译转载)。
原文
BACKGROUND: Taper corrosion in total hip arthroplasty for bearings with metal heads against polyethylene has developed from an anecdotal observation to a clinical problem. Increased taper wear and even gross taper failure have been reported for one particular design. It is hypothesized that corrosion of the female head taper results in taper widening, allowing the cobalt-chromium head to turn on the stem and wear down the softer titanium alloy by abrasive wear, ultimately causing failure. The purpose of this study is to investigate the time course of this process and the general role of taper dimensions and material in this problem. METHODS: Retrieved cobalt-chromium alloy heads (n = 30, LFIT; Stryker, Mahwah, NJ) and Ti-12Mo-6Zr-2Fe (TMZF) stems (n = 10, Accolade I; Stryker) were available for analysis. Taper material loss was determined using three-dimensional coordinate measurements and scanning. The pristine tip clearance between head and stem was analytically determined. The influence of taper material and taper size on taper deformation and micromotion was investigated using a finite element model. RESULTS: Material loss at the head taper increased with time in situ up to a volume of 20.8 mm3 (P < .001). A mean linear material loss above 76 μm at the head taper was analytically confirmed to result in bottoming out, which was observed in 12 heads. The finite element calculations showed significantly larger deformations and micromotions for a small 11/13 TMZF taper combined with a distinctly different micromotion pattern compared to other materials and taper designs. CONCLUSION: A 11/13 TMZF taper design with 36-mm head diameters bears a higher risk for corrosion than larger tapers made from stiffer materials. Failures of this combination are not restricted to the head sizes included in the recall. Patients with this implant combination should be closely monitored.
引用
- Morlock MM, Dickinson EC, Günther KP, et al. Head Taper Corrosion Causing Head Bottoming Out and Consecutive Gross Stem Taper Failure in Total Hip Arthroplasty. J Arthroplasty. 2018. PMID: 30100136. doi:10.1016/j.arth.2018.07.017
供执业医师工作参考,不替代临床判断;数值与分级以指南原文为准。