肩袖修复的生物力学强度:尸体研究的系统综述与Meta回归分析
该系统综述纳入40项尸体生物力学研究,采用Meta回归分析评估肩袖修复构建的技术参数对生物力学性能的预测作用。结果显示缝线股数、缝线数量及褥式缝合数量是比构建类型更强的整体强度预测因素,且缝线股数增加与极限失败载荷升高和间隙形成减少相关。
要点
- 缝线股数每增加1股,极限失败载荷增加38 N(95%CI 28-49 N),间隙形成减少0.6 mm(95%CI -1至-0.2 mm)。
- 控制缝线股数后,单排锚钉、双排锚钉、经骨等效及经骨修复之间无显著差异。
- 缝线股数和经骨等效修复均增加灾难性构建失败的概率。
核心结论
- 该研究表明肩袖修复构建中缝线数量、缝线股数和褥式缝合数量比构建类型更能预测整体强度。
- 需要在增加构建强度与更高的2型失败风险之间取得平衡。
研究设计与样本
- 系统综述,系统检索EMBASE和PubMed数据库中测量尸体标本肩袖修复性能的生物力学研究。
- 对汇总数据集进行Meta回归,以研究结局(间隙形成、失败模式、极限失败载荷)为因变量,以手术参数(如构建类型、缝线股数)为协变量,并进行协变量分层分析,α水平为0.05。
- 共纳入40项符合条件的研究的数据。
主要发现
- 较高的缝线股数与较高的极限失败载荷相关(β=38 N/股;95%CI 28至49 N)。
- 较高的缝线股数与较少的间隙形成相关(β=-0.6 mm/股;95%CI -1至-0.2 mm)。
- 极限失败载荷的其他阳性预测因素包括缝线数量、褥式缝合数量以及使用宽缝线对比标准缝线。
- 控制缝线股数后,单排锚钉、双排锚钉、经骨等效和经骨修复之间无显著差异。
- 较高的缝线股数和经骨等效修复均增加灾难性构建失败的概率。
关键数值与推荐
- 缝线股数每增加1股,极限失败载荷增加38 N(95%CI 28至49 N)。
- 缝线股数每增加1股,间隙形成减少0.6 mm(95%CI -1至-0.2 mm)。
局限性
- 原文未报告局限性。
以上解读依据论文摘要(全文未开放获取或许可不允许翻译转载)。
原文
BACKGROUND: Biomechanical cadaveric studies of rotator cuff repair (RCR) have shown that transosseous equivalent and double-row anchored repairs are stronger than other repair constructs. PURPOSE: To identify technical and procedural parameters that most reliably predict biomechanical performance of RCR constructs. STUDY DESIGN: Systematic review. METHODS: The authors systematically searched the EMBASE and PubMed databases for biomechanical studies that measured RCR performance in cadaveric specimens. The authors performed a meta-regression on the pooled data set with study outcomes (gap formation, failure mode, and ultimate failure load) as dependent variables and procedural parameters (eg, construct type, number of suture limbs) as covariates. Stratification by covariates was performed. An alpha level of .05 was used. RESULTS: Data from 40 eligible studies were included. Higher number of suture limbs correlated with higher ultimate failure load (β = 38 N per limb; 95% CI, 28 to 49 N) and less gap formation (β = -0.6 mm per limb; 95% CI, -1 to -0.2 mm). Other positive predictors of ultimate failure load were number of sutures, number of mattress stitches, and use of wide suture versus standard suture. When controlling for number of suture limbs, we found no significant differences among single-row anchored, double-row anchored, transosseous equivalent, and transosseous repairs. Higher number of suture limbs and transosseous equivalent repair both increased the probability of catastrophic construct failure. CONCLUSION: This study suggests that the number of sutures, suture limbs, and mattress stitches in a RCR construct are stronger predictors of overall strength than is construct type. There is a need to balance increased construct strength with higher risk of type 2 failure.
引用
- Shi BY, Diaz M, Binkley M, et al. Biomechanical Strength of Rotator Cuff Repairs: A Systematic Review and Meta-regression Analysis of Cadaveric Studies. Am J Sports Med. 2018. PMID: 29975549. doi:10.1177/0363546518780928
供执业医师工作参考,不替代临床判断;数值与分级以指南原文为准。