基于尸体特异性有限元分析的双动髋关节假体髂腰肌撞击模型
本研究基于既往尸体实验,对10条尸体髂腰肌腱测量线性刚度(平均339.4 N/mm)并作为有限元分析输入,比较解剖轮廓型与传统双动髋关节假体在髋屈曲过程中的髂腰肌腱-内衬接触压力和肌腱应力。结果显示两种假体的接触压力与von Mises应力均随髋屈曲增加而降低,解剖轮廓型假体在所有标本和屈曲角度下平均接触压力与von Mises应力均低于传统假体。作者认为解剖轮廓设计可能成为使用大股骨头假体时避免前方软组织撞击的解决方案。
要点
- 10条尸体髂腰肌腱拉伸测试平均线性刚度为339.4 N/mm,作为有限元分析输入。
- 两种双动假体的肌腱-内衬接触压力和肌腱von Mises应力均随髋屈曲角度增加而降低。
- 解剖轮廓型假体在所有标本和髋屈曲角度下平均接触压力与von Mises应力均低于传统假体。
核心结论
- 基于既往尸体研究显示解剖轮廓设计较传统双动假体减少髂腰肌腱帐篷样隆起,本尸体特异性有限元分析发现解剖轮廓型双动内衬可降低肌腱-内衬接触压力和肌腱应力。
- 作者认为解剖轮廓设计可能成为使用大股骨头髋关节假体时避免前方软组织撞击的解决方案。
研究设计与样本
- 基于尸体的有限元分析研究,测量10条髂腰肌腱的刚度,并依据既往尸体实验对2种假体设计进行三维骨模型、接触压力和髂腰肌腱应力评估。
主要发现
- 尸体髂腰肌腱拉伸测试显示平均线性刚度为339.4 N/mm,该值被用作有限元分析的输入。
- 两种假体的肌腱-内衬接触压力和肌腱von Mises应力均随髋屈曲角度增加而降低。
- 解剖轮廓型设计的平均接触压力和von Mises应力在所有标本和所有髋屈曲角度下均低于传统假体。
局限性
- 原文未报告局限性。
以上解读依据论文摘要(全文未开放获取或许可不允许翻译转载)。
原文
BACKGROUND: Joint dislocation is a major cause of failure in total hip arthroplasty. Dual-mobility implants provide a femoral head diameter that can match the native hip size for greater stability against dislocation. However, such large heads are prone to impingement against surrounding soft tissues. To address this concern, the concept of an anatomically contoured dual-mobility implant was evaluated using cadaver-specific finite-element analysis (FEA). METHODS: The stiffness of 10 iliopsoas tendons was measured and also 3D bone models, contact pressure, and iliopsoas tendon stress were evaluated for 2 implant designs according to a previous cadaveric experiment. The iliopsoas interaction with an anatomically contoured and conventional dual-mobility implant was analyzed throughout hip flexion. RESULTS: The tensile test of cadaveric iliopsoas tendons revealed an average linear stiffness of 339.4 N/mm, which was used as an input for the FEA. Tendon-liner contact pressure and tendon von Mises stress decreased with increasing hip flexion for both implants. Average contact pressure and von Mises stresses were lower in the anatomically contoured design compared with the conventional implant across all specimens and hip flexion angles. CONCLUSIONS: This study was built upon a previous cadaver study showing reduced tenting of the iliopsoas tendon for an anatomically contoured design compared with a conventional dual-mobility implant. The present cadaver-specific FEA study found reduced tendon-liner contact pressure and tendon stresses with contoured dual-mobility liners. Anatomical contoured design may be a solution to avoid anterior soft-tissue impingement when using hip prostheses with large femoral heads.
引用
- Zumbrunn T, Patel R, Duffy MP, et al. Cadaver-Specific Models for Finite-Element Analysis of Iliopsoas Impingement in Dual-Mobility Hip Implants. J Arthroplasty. 2018. PMID: 30029930. doi:10.1016/j.arth.2018.06.029
供执业医师工作参考,不替代临床判断;数值与分级以指南原文为准。