文献速递关节外科

骨盆位置对髋臼假体位置影像学评估的定量影响

Quantitative Effect of Pelvic Position on Radiographic Assessment of Acetabular Component Position.
PubMed 文献 · J Arthroplasty · 2017-09-25

在全髋关节置换模拟仰卧位模型中,骨盆旋转和倾斜以5°递增、射线束中心偏移以1 cm递增时,髋臼假体前倾角和外展角的测量偏差随骨盆位置偏离呈指数增加,前倾角偏差大于外展角;射线束中心在冠状面偏移5 cm以内未引入大于5°的测量偏差。

要点

  • 骨盆旋转和倾斜偏离越大,髋臼假体前倾角和外展角的测量偏差呈指数增加。
  • 前倾角的测量偏差大于外展角。
  • 以髋关节为中心的图像比以骨盆为中心的图像受骨盆位置不良影响更小。

核心结论

  • 髋臼假体外展角和前倾角的准确测量对骨盆相对于所选放射学平面的位置敏感,尤其是前倾角。
  • 当骨盆方向处于新确定的最近骨盆位置范围内时,可获得±5°的可接受测量偏差。

研究设计与样本

  • 在模拟仰卧位全髋关节置换模型上,使用已知髋臼假体位置的骨盆模型获取骨盆和髋关节后前位图像。
  • 骨盆位置以骨盆旋转(髂骨-闭孔)和倾斜(入口-出口)5°递增变化,射线束中心以颅尾和内外侧平面1 cm递增偏移。
  • 采用多元回归分析评估假体位置解读偏差与骨盆位置的关系。

主要发现

  • 前倾角和外展角测量偏差随旋转和倾斜偏离增加呈指数增加。
  • 前倾角的偏差大于外展角。
  • 以髋关节为中心的图像受骨盆位置不良影响小于以骨盆为中心的图像。
  • 射线束中心在冠状面偏移5 cm以内未引入大于5°的测量偏差。
  • 采用外展角和前倾角±5°的任意可接受偏差,分别确定了以髋关节和以骨盆为中心成像的最佳骨盆位置范围。

关键数值与推荐

  • 外展角和前倾角的可接受测量偏差定义为±5°。
  • 射线束中心在冠状面偏移5 cm以内未引入大于5°的测量偏差。

局限性

  • 原文未报告局限性。

以上解读依据论文摘要(全文未开放获取或许可不允许翻译转载)。

原文

BACKGROUND: Intraoperative fluoroscopy aims to improve component position in total hip arthroplasty. Measurement bias related to image quality, however, has not been quantified. We aim to quantify measurement bias in the interpretation of acetabular component position as a function of pelvis and fluoroscopic beam position in a simulated supine total hip arthroplasty model. METHODS: Posterior-anterior pelvis and hip images were obtained using a previously described pelvic model with known acetabular component position. Pelvic position was varied in 5° increments of pelvis rotation (iliac-obturator) and tilt (inlet-outlet), and in 1 cm increments from beam center in cranial-caudal and medial-lateral planes. Multiple regression analyses were conducted to evaluate the relationship between the resulting bias in interpretation of component position relative to pelvis position. RESULTS: Anteversion and abduction measurement bias increased exponentially with increasing deviation in rotation and tilt. Greater bias occurred for anteversion than for abduction. Hip centered images were less affected by pelvis malposition than pelvis centered images. Deviations of beam center within 5 cm in the coronal plane did not introduce measurement bias greater than 5°. An arbitrarily defined acceptable bias of ±5° for both abduction and anteversion was used to identify a range of optimum pelvic positioning each for hip and pelvis centered imaging. CONCLUSION: Accurate measurement of acetabular component abduction and anteversion, especially anteversion, is sensitive to proper pelvic position relative to the chosen radiographic plane. An acceptable measurement bias of ±5° is achieved when the pelvis is oriented within a newly identified range of optimum pelvic positioning.

来源:J Arthroplasty,查看原文。版权归原作者所有。

引用

  1. Delagrammaticas DE, Alvi HM, Kaat AJ, et al. Quantitative Effect of Pelvic Position on Radiographic Assessment of Acetabular Component Position. J Arthroplasty. 2017. PMID: 29066106. doi:10.1016/j.arth.2017.09.033

供执业医师工作参考,不替代临床判断;数值与分级以指南原文为准。