文献速递关节外科

单中心钛制模块化颈全髋关节置换术经验

A Single-Center Experience With a Titanium Modular Neck Total Hip Arthroplasty.
PubMed 文献 · J Arthroplasty · 2017-03-20

回顾性分析2005至2012年809例全髋关节置换术,平均随访5.7年,评估钛-钛模块化颈-柄接口的并发症、影响颈模块化使用的临床因素及模块化是否降低脱位发生率。结果显示颈骨折率0.5%、脱位率1.1%,后路入路增加模块化使用最多且脱位率最高(2.3%),增加模块化使用可能未改善后路入路的脱位风险。

要点

  • 平均随访5.7年,颈骨折率0.5%(4/809),总脱位率1.1%(9/809)。
  • 后路入路增加模块化使用率39.4%,高于前路6.8%和侧路23.7%。
  • 后路入路脱位率最高(2.3%),前路0.3%、侧路0%。

核心结论

  • 平均随访5.7年,本中心经验显示低颈骨折率(0.5%)和低脱位率(1.1%)。
  • 增加模块化使用可能未改善后路入路的脱位风险。
  • 需持续监测该组患者以确定该模块化钛植入物的长期生存率。

研究设计与样本

  • 单中心回顾性队列研究,数据来自前瞻性收集的数据库。
  • 纳入2005年至2012年间完成的809例全髋关节置换术,平均随访5.7年(范围3.3-10.3年)。
  • 男性360例(45%),女性449例(55%);所有股骨柄均为非骨水泥型PROFEMUR TL(钛、平锥形、楔形)或PROFEMUR Z(钛、矩形、双锥形),配钛制颈。

主要发现

  • 增加模块化(前倾/后倾及前倾/后倾内翻/外翻)在后路入路中使用率为39.4%(135/343),前路为6.8%(20/293),侧路为23.7%(41/173)。
  • 4例男性在初次手术后平均95.5个月(范围69.3-115.6个月)发生颈骨折。
  • 总体脱位率为1.1%(9/809);后路入路脱位率最高(2.3%),其中多数为复发性;前路脱位率为0.3%、侧路为0%,且无复发性脱位。

局限性

  • 原文未报告局限性。

以上解读依据论文摘要(全文未开放获取或许可不允许翻译转载)。

原文

BACKGROUND: Added modular junction has been associated with implant-related failures. We report our experience with a titanium-titanium modular neck-stem interface to assess complications, possible clinical factors influencing use of neck modularity, and whether modularity reduced the incidence of dislocation. METHODS: A total of 809 total hip arthroplasties completed between 2005 and 2012 from a prospectively collected database were reviewed. The mean follow-up interval was 5.7 years (3.3-10.3 years). Forty-five percent were male (360 of 809), and 55% were female (449 of 809). All stems were uncemented PROFEMUR TL (titanium, flat-tapered, wedge) or PROFEMUR Z (titanium, rectangular, dual-tapered) with a titanium neck. RESULTS: Increased modularity (anteverted/retroverted and anteverted/retroverted varus/valgus (anteverted/retroverted + anteverted/retroverted varus/valgus) was used in 39.4% (135 of 343) of cases using the posterior approach compared with 6.8% (20 of 293) of anterior and 23.7% (41 of 173) of lateral approaches. Four males sustained neck fractures at a mean of 95.5 months (69.3-115.6 months) after primary surgery. Overall dislocation rate was 1.1% (9 of 809). The posterior approach had both the highest utilization of increased modularity and the highest dislocation rate (2.3%), of which the most were recurrent. The anterior (0.3%) and lateral (0%) approaches had lower dislocation rates with no recurrences. CONCLUSION: At a mean 5.7 years, our experience demonstrates a low neck fracture (0.5%) and a low dislocation rate (1.1%). Use of increased modularity may not improve dislocation risk for the posterior approach. Continued surveillance of this group will be necessary to determine long term survivorship of this modular titanium implant.

来源:J Arthroplasty,查看原文。版权归原作者所有。

引用

  1. Gofton WT, Illical EM, Feibel RJ, et al. A Single-Center Experience With a Titanium Modular Neck Total Hip Arthroplasty. J Arthroplasty. 2017. PMID: 28479057. doi:10.1016/j.arth.2017.03.025

供执业医师工作参考,不替代临床判断;数值与分级以指南原文为准。