青少年特发性脊柱侧凸的几何扭转:区分Lenke 1亚型的新方法
该连续病例系列纳入141例Lenke 1型青少年特发性脊柱侧凸患者,利用双平面X线三维重建计算胸腰段中性椎的几何扭转。Lenke 1A扭转(1.15 mm)与1C(2.10 mm)差异有统计学意义,1B(1.75 mm)与两者均无差异;自动分类得出高扭转组(3.02 mm)与低扭转组(0.82 mm),两组主胸弯及胸腰/腰弯最大曲率平面方向差异有统计学意义。作者认为三维数值化描述脊柱侧凸可行,并提示存在与最大曲率平面方向相关的两个扭转亚组。
要点
- Lenke 1A扭转1.15 mm vs 1C 2.10 mm,差异有统计学意义。
- Lenke 1B扭转1.75 mm,与1A、1C两组均无差异。
- 自动分类高扭转组3.02 mm vs 低扭转组0.82 mm。
核心结论
- 作者认为,用数值方法在三维层面描述脊柱侧凸是可达成的。
- 作者认为,基于扭转值存在高扭转与低扭转两个三维形变亚组,并与最大曲率平面方向相关。
研究设计与样本
- 研究设计为连续病例系列,证据等级为4级。
- 纳入本机构141例Lenke 1型畸形患者,由两名观察者判定Lenke分型,并用双平面X线获取三维重建。
- 采用新技术通过近似胸腰段中性椎的局部弧长计算几何扭转,并行组间与组内统计分析评估扭转指数及其与其他三维指标的关系。
主要发现
- Lenke 1A组扭转1.15 mm vs Lenke 1C组2.10 mm,差异有统计学意义。
- Lenke 1B组扭转1.75 mm,与Lenke 1A组和Lenke 1C组均无差异。
- 基于扭转指数的自动分类识别出高扭转组3.02 mm与低扭转组0.82 mm。
- 主胸弯最大曲率平面方向:高扭转组73.72° vs 低扭转组79.85°,差异有统计学意义。
- 胸腰/腰弯最大曲率平面方向:高扭转组56.41° vs 低扭转组49.25°,差异有统计学意义。
局限性
- 原文未报告局限性。
以上解读依据论文摘要(全文未开放获取或许可不允许翻译转载)。
原文
STUDY DESIGN: Consecutive case series. OBJECTIVE: To study geometric torsion in thoracic adolescent idiopathic scoliosis (AIS) to propose it as a numerical three-dimensional (3D) parameter that quantifies the scoliosis deformity. SUMMARY OF BACKGROUND DATA: AIS is a 3D deformity of the spine. The most widely accepted and used classification systems, however, still rely on two-dimensional aspects of x-rays. Yet, a 3D classification of AIS remains elusive because there is no widely accepted 3D parameter in the clinical practice. METHODS: Analysis of 141 patients with Lenke type-1 deformity recruited in our institution. The Lenke classification was identified by two observers and 3D reconstructions were obtained using biplanar radiographs. Geometric torsion measuring the twisting effect of the spine was computed using a novel technique by approximating local arc lengths at the neutral vertebra in the thoracolumbar segment. An inter- and intragroup statistical analysis was performed to evaluate the torsion index, and how it relates to other 3D indices. RESULTS: A statistically significant increase in torsion was observed between Lenke 1A (1.15 mm) and Lenke 1C (2.10 mm) subgroups. No differences were found between the Lenke 1B (1.75 mm) subgroup with either of the other two subgroups. An automatic classification based on torsion indices identified two groups: one with high torsion values (3.02 mm) and one with low torsion values (0.82 mm). Statistically significant differences were found between the main thoracic planes of maximum curvature (PMC) orientation of the high-torsion group (73.72°) and the low-torsion group (79.85°). Statistically significant differences were also found for the thoracolumbar/lumbar PMC orientation between the high-torsion group (56.41°) and the low-torsion group (49.25°). CONCLUSION: These results suggest that a numerical method of describing scoliosis in 3D is within reach. They also suggest the existence of two subgroups of 3D deformations based on torsion values (high and low) with links to PMC orientation. LEVEL OF EVIDENCE: 4.
引用
- Shen J, Kadoury S, Labelle H, et al. Geometric Torsion in Adolescent Idiopathic Scoliosis: A New Method to Differentiate Between Lenke 1 Subtypes. Spine (Phila Pa 1976). 2017. PMID: 28441683. doi:10.1097/BRS.0000000000001866
供执业医师工作参考,不替代临床判断;数值与分级以指南原文为准。