文献速递关节外科

最大胫骨假体外旋是否影响初次膝关节置换中的胫股负荷分布:中立位与最大解剖外旋状态的比较

Does Maximal External Tibial Component Rotation Influence Tibiofemoral Load Distribution in the Primary Knee Arthroplasty Setting: A Comparison of Neutral vs Maximal Anatomical External Rotatory States.
PubMed 文献 · J Arthroplasty · 2017-02-01

在尸体模型上,利用计算机导航和三维位移测量及骨传感器连续负荷传感器,比较胫骨假体最大外旋与中立位对松弛度和胫股连续负荷的影响。结果显示两种状态在0-115度屈曲弧内最大内/外翻或旋转松弛度无显著差异,中立位在各屈曲点实现内外侧负荷分布等效;外旋较中立位增加内侧间室负荷,并持续引起外侧负荷边际性但不显著的降低,效应在屈曲中期最明显。作者据此主张以胫骨结节中点确定胫骨假体旋转,并告诫避免假体外旋。

要点

  • 在0-115度屈曲弧内,最大内/外翻或旋转松弛度在最大外旋与中立位之间无显著差异。
  • 中立位在各屈曲点实现内外侧负荷分布等效。
  • 胫骨假体外旋较中立位增加内侧间室负荷,外侧负荷呈边际性但不显著的降低。

核心结论

  • 基于这些发现,作者主张以胫骨结节中点确定胫骨假体旋转,并告诫避免假体外旋。

研究设计与样本

  • 尸体模型研究,使用计算机导航,在模拟体内设定的既定、先前验证的负荷条件下,通过三维位移测量和植入聚乙烯垫片内的骨传感器连续负荷传感器,在模拟单半径全膝关节置换中比较胫骨假体最大外旋与中立位对松弛度和胫股连续负荷的影响。

主要发现

  • 在0-115度屈曲弧内,最大内翻和/或外翻或旋转松弛度在最大外旋与中立位两种状态之间无显著差异。
  • 中立位在各屈曲点实现内外侧负荷分布等效。
  • 与中立位相比,胫骨假体外旋增加内侧间室负荷。
  • 与中立位相比,外旋在相似负荷条件下持续引起外侧负荷边际性但不显著的降低。
  • 这些效应在屈曲中期最明显。

临床怎么用

  • 作者主张以胫骨结节中点确定胫骨假体旋转,并告诫避免假体外旋。

局限性

  • 原文未报告局限性。

以上解读依据论文摘要(全文未开放获取或许可不允许翻译转载)。

原文

BACKGROUND: Tibial component rotation at time of knee arthroplasty can influence conformity, load transmission across the polyethylene surface, and perhaps ultimately determined survivorship. Optimal tibial component rotation on the cut surface is reliant on standard per operative manual stressing. This subjective assessment aims to balance constraint and stability of the articulation through a full arc of movement. METHODS: Using a cadaveric model, computer navigation and under defined, previously validated loaded conditions mimicking the in vivo setting, the influence of maximal tibial component external rotation compared with the neutral state was examined for changes in laxity and tibiofemoral continuous load using 3D displacement measurement and an orthosensor continuous load sensor implanted within the polyethylene spacer in a simulated single radius total knee arthroplasty. RESULTS: No significant difference was found throughout arc of motion (0-115 degrees of flexion) for maximal varus and/or valgus or rotatory laxity between the 2 states. The neutral state achieved equivalence for mediolateral load distribution at each point of flexion. We have found that external rotation of the tibial component increased medial compartment load in comparison with the neutral position. Compared with the neutral state, external rotation consistently effected a marginal, but not significant reduction in lateral load under similar loading conditions. The effects were most pronounced in midflexion. CONCLUSION: On the basis of these findings, we would advocate for the midtibial tubercle point to determine tibial component rotation and caution against component external rotation.

来源:J Arthroplasty,查看原文。版权归原作者所有。

引用

  1. Manning WA, Ghosh KM, Blain AP, et al. Does Maximal External Tibial Component Rotation Influence Tibiofemoral Load Distribution in the Primary Knee Arthroplasty Setting: A Comparison of Neutral vs Maximal Anatomical External Rotatory States. J Arthroplasty. 2017. PMID: 28236553. doi:10.1016/j.arth.2017.01.035

供执业医师工作参考,不替代临床判断;数值与分级以指南原文为准。