文献速递脊柱外科

采用独立U形椎间盘植入物的双节段颈椎间盘置换生物力学分析

Biomechanical Analysis of Two-level Cervical Disc Replacement With a Stand-alone U-shaped Disc Implant.
PubMed 文献 · Spine (Phila Pa 1976) · 2017-01-01

本研究利用三维非线性有限元模型,在C4-C6节段植入Mobi-C、PCM和DCI三种假体,分析双节段置换后的生物力学变化。结果显示DCI在保留运动和储存能量方面接近正常椎间盘,且DCI与PCM在节段间软骨的应力低于Mobi-C,可能在一定程度上避免小关节退变。

要点

  • DCI在伸展和屈曲时的运动分布与完整模型较为接近。
  • Mobi-C和PCM明显增加手术节段伸展活动度,但均导致伸展力矩下降约45%。
  • Mobi-C增加的小关节最大应力约39%,而DCI未在节段间软骨产生明显过载。

核心结论

  • 每种假体各有生物力学优缺点,但DCI能够像正常椎间盘一样在外部载荷下保留运动并储存能量。
  • 与Mobi-C相比,DCI和PCM在节段间软骨的应力更低,可能在一定程度上避免小关节退变。
  • 这种结构独立的控制型关节置换装置可能是有潜力的候选方案,需在未來研究中进一步探讨。

研究设计与样本

  • 采用三维非线性有限元模型进行生物力学研究,在C4-C6椎间盘间隙植入Mobi-C、多孔涂层运动(PCM)和DCI三种假体,于C3终板中心施加位移载荷模拟屈伸运动。

主要发现

  • DCI在伸展时以及DCI和Mobi-C在屈曲时的运动分布与完整模型较为接近。
  • Mobi-C和PCM明显增加手术节段的联合伸展活动度,但两者均导致伸展力矩下降约45%。
  • DCI的应变能趋势与健康椎间盘相似;PCM的小关节应力分布与完整模型几乎相似。
  • DCI未在节段间软骨产生明显过载,而Mobi-C增加的小关节最大应力约39%。
  • 超高分子量聚乙烯芯的最大应力高于屈服应力(Mobi-C为42.43 MPa,PCM为30.94 MPa)。

局限性

  • 原文未报告局限性。

以上解读依据论文摘要(全文未开放获取或许可不允许翻译转载)。

原文

STUDY DESIGN: Biomechanical study using a three-dimensional nonlinear finite element model. OBJECTIVE: To analyze biomechanical changes with three prostheses based on two-level arthroplasty and to verify the biomechanical efficiency of dynamic cervical implants (DCIs) with a stand-alone U-shaped structure. SUMMARY OF BACKGROUND DATA: Few studies have compared biomechanical behavior of various prostheses as they relate with clinical results after two-level total disc replacement. METHODS: Three arthroplasty devices Mobi-C, porous coated motion (PCM), and DCI were inserted at the C4-C6 disc space and analyzed. Displacement loading was applied to the center of the endplate at the C3 level to simulate flexion and extension motions. RESULTS: The motion distributions in extension with DCI and in flexion with DCI and Mobi-C were relatively close to that in the intact model. Mobi-C and PCM obviously increased the combined extension range of motion at the index levels, but both resulted in about 45% decrease in extension moment. DCI showed a trend in strain energy similar to that of healthy discs. PCM exhibited a facet joint stress distribution almost similar to that of the intact model. DCI did not generate significant overloading at cartilage between the index levels, whereas the maximum facet joint stress increased with Mobi-C was about 39%. The maximum stress on a ultrahigh molecular-weight-polyethylene core was above the yield stress (42.43 MPa for Mobi-C and 30.94 MPa for PCM). CONCLUSION: Each prosthesis shows its biomechanical advantages and disadvantages. However, DCI has the capacity to preserve motion and store energy under external loading, similar to the behavior of normal discs. Compared with Mobi-C, both DCI and PCM showed a lower stress at cartilage between index levels, which may avoid facet joint degeneration to some extent. Such a well-controlled arthroplasty device with a stand-alone structure may be a potential candidate and needs to be investigated in future studies. LEVEL OF EVIDENCE: 5.

来源:Spine (Phila Pa 1976),查看原文。版权归原作者所有。

引用

  1. Li Y, Fogel GR, Liao Z, et al. Biomechanical Analysis of Two-level Cervical Disc Replacement With a Stand-alone U-shaped Disc Implant. Spine (Phila Pa 1976). 2017. PMID: 28198781. doi:10.1097/BRS.0000000000002128

供执业医师工作参考,不替代临床判断;数值与分级以指南原文为准。