预防性环扎钢丝在初次全髋关节置换术中的作用:一项生物力学研究
研究采用10对匹配的新鲜冷冻尸体股骨,植入解剖型锥形非骨水泥股骨柄,比较加与不加2根单丝股骨距环扎钢丝在轴向加载与外旋至失败时的生物力学参数。结果显示加钢丝标本的失败旋转角度(P=.039)和失败能量(P=.048)显著更高,初始扭转刚度(P=.63)和失败扭矩(P=.10)无显著差异。作者认为预防性环扎钢丝可增加良好压配股骨植入物的旋转和失败能量,但需进一步研究评估成本效益与长期结局,并建议根据具体情况考虑预防性环扎。
要点
- 加环扎钢丝标本失败时所需旋转角度显著大于不加钢丝标本(P=.039)。
- 加环扎钢丝标本失败时所需能量显著大于不加钢丝标本(P=.048)。
- 初始扭转刚度和失败扭矩在两组间无显著差异(P=.63和P=.10)。
核心结论
- 预防性环扎钢丝放置可增加良好固定的压配股骨植入物的失败旋转和能量。
- 失败所需扭转能量的增加可能降低早期假体周围骨折的风险。
- 需要进一步研究评估预防性环扎的成本效益与长期结局。
- 根据本研究结果,预防性环扎的考虑应基于具体病例逐一评估。
研究设计与样本
- 研究为生物力学研究,采用10对匹配的新鲜冷冻尸体股骨。
- 标本植入解剖型锥形非骨水泥股骨柄,分为加2根单丝股骨距环扎钢丝组和不加钢丝组。
- 标本进行轴向加载和外旋至失败,测量初始扭转刚度、失败旋转、失败能量和失败扭矩。
- 统计学显著性设定为P<.05,骨折模式按一种知名分类系统分类。
主要发现
- 加钢丝标本失败时所需旋转显著大于不加钢丝标本(P=.039)。
- 加钢丝标本失败时所需能量显著大于不加钢丝标本(P=.048)。
- 初始扭转刚度在不加钢丝组与加钢丝组间无显著差异(P=.63)。
- 失败扭矩在不加钢丝组与加钢丝组间无显著差异(P=.10)。
- 所有不加钢丝标本均发生Vancouver B2型骨折模式;8个加钢丝标本中7个也发生Vancouver B2型骨折模式,第8个加钢丝标本发生Vancouver B1型骨折模式。
临床怎么用
- 作者认为,基于本研究结果,预防性环扎的考虑应基于具体病例逐一评估。
局限性
- 需要进一步研究评估预防性环扎的成本效益与长期结局。
以上解读依据论文摘要(全文未开放获取或许可不允许翻译转载)。
原文
BACKGROUND: Despite literature to support the use of various cerclage techniques to address intraoperative femoral fractures in total hip arthroplasty, there are limited data to support prophylactic cerclage wiring of the femur during cementless implant placement. This study aims to evaluate the effect of prophylactic calcar cerclage wires on the biomechanical parameters required to produce periprosthetic femoral fractures and on the morphology of these fracture patterns in stable cementless femoral implants. METHODS: Ten pairs of matched fresh frozen cadaveric femurs were implanted with anatomic tapered cementless implants with or without the addition of 2 monofilament calcar wires. Specimens were axially loaded and externally rotated to failure. Initial torsional stiffness, rotation and energy to failure, and torque at failure were measured. Statistical significance was set at P < .05. Fracture patterns were classified according to a well-known classification system. RESULTS: Wired specimens required significantly more rotation (P = .039) and energy to failure (P = .048). No significant difference was detected in initial torsional stiffness (P = .63) or torque at failure (P = .10). All unwired samples developed a Vancouver B2 fracture pattern. Seven of the 8 wired specimens also developed a Vancouver B2 fracture pattern, while the eighth wired specimen developed a Vancouver B1 fracture pattern. CONCLUSION: Prophylactic cerclage wire placement increases the rotation and energy to failure in well-fixed press-fit femoral implants. The increase in torsional energy needed for failure may reduce the risk of early periprosthetic fracture. Further studies are needed to evaluate cost vs benefit and long-term outcomes of prophylactic wiring. Based on the results of our study, consideration of prophylactic wiring should be addressed on a case-to-case basis.
引用
- Waligora AC, Owen JR, Wayne JS, et al. The Effect of Prophylactic Cerclage Wires in Primary Total Hip Arthroplasty: A Biomechanical Study. J Arthroplasty. 2017. PMID: 28209401. doi:10.1016/j.arth.2017.01.019
供执业医师工作参考,不替代临床判断;数值与分级以指南原文为准。