初次全髋关节置换术数字模板的准确性:直接前入路与后入路之间是否存在差异?
本研究纳入同一术者连续完成的131例患者(148髋)初次全髋关节置换术,比较直接前入路(DAA,使用可透射线手术台与术中透视)与后入路(PA)在数字模板预测假体尺寸和偏移方面的准确性。结果显示,DAA组杯臼尺寸预测在2mm以内的准确率为91%,PA组为88%(P=0.61);股骨柄尺寸预测在1个尺寸以内的准确率DAA组为85%,PA组为77%(P=0.71);两组在股骨柄颈干角和股骨偏移预测上也无显著差异。结论认为,无论采用PA还是DAA联合透视,数字模板均是预测全髋关节置换术假体尺寸和偏移的可靠且高度准确的方法。
要点
- DAA组杯臼尺寸预测在2mm以内的准确率为91%,PA组为88%,两组差异无统计学意义(P=0.61)。
- DAA组股骨柄尺寸预测在1个尺寸以内的准确率为85%,PA组为77%,两组差异无统计学意义(P=0.71)。
- 两组在预测最终股骨柄颈干角或股骨偏移方面均无显著差异。
核心结论
- 数字模板是预测全髋关节置换术假体尺寸和偏移的可靠且高度准确的方法,无论采用后入路还是直接前入路联合透视。
研究设计与样本
- 同一术者连续完成的131例患者(148髋)初次全髋关节置换术,使用相同的杯臼和股骨柄设计。
- 75髋采用直接前入路(DAA),使用骨折手术台和透视;73髋采用后入路(PA),患者侧卧位使用标准体位架,不使用透视。
- 术前X线片由同一术者进行数字模板规划。
主要发现
- PA组患者平均体重指数更高,且术前诊断股骨头缺血性坏死的比例更高。
- 杯臼尺寸预测在2mm以内的准确率:DAA组91% vs PA组88%(P=0.61)。
- 股骨柄尺寸预测在1个尺寸以内的准确率:DAA组85% vs PA组77%(P=0.71)。
- 两组在预测最终股骨柄颈干角或股骨偏移方面均无显著差异。
局限性
- 原文未报告局限性
以上解读依据论文摘要(全文未开放获取或许可不允许翻译转载)。
原文
BACKGROUND: The direct anterior approach (DAA) has gained recent popularity for total hip arthroplasty (THA), as it provides immediate feedback on cup position and limb length using fluoroscopy. The purpose of this study is to evaluate any differences in the accuracy of digital templating for preoperative planning of THA, performed with 2 different surgical approaches: DAA using a radiolucent table with intraoperative fluoroscopy and the posterior approach (PA). METHODS: One hundred thirty-one consecutive patients (148 hips) underwent a THA by a single surgeon, using the same cup and stem designs. Seventy-five hips were performed using the DAA using a fracture table and fluoroscopy. Seventy-three hips were performed using the PA with the patient positioned in lateral decubitus using standard positioners without fluoroscopy. Preoperative radiographs were digitally templated by the same surgeon. RESULTS: The PA patients had a higher mean body mass index and were more likely to have a preoperative diagnosis of avascular necrosis. The accuracy of templating for predicting the cup size to be within 2 mm was 91% for DAA vs 88% for PA (P = .61). For stem size, the accuracy was 85% (to within 1 size) for the DAA vs 77% for the PA (P = .71). Likewise, there was no significant difference in predicting the final stem's neck angle or femoral offset. CONCLUSION: Digital templating was found to be a reliable and highly accurate method for predicting component sizes and offset for THA, regardless of using either the PA or the DAA with fluoroscopy.
引用
- Shemesh SS, Robinson J, Keswani A, et al. The Accuracy of Digital Templating for Primary Total Hip Arthroplasty: Is There a Difference Between Direct Anterior and Posterior Approaches? J Arthroplasty. 2016. PMID: 28108172. doi:10.1016/j.arth.2016.12.032
供执业医师工作参考,不替代临床判断;数值与分级以指南原文为准。