解剖型胫骨假体在人工全膝关节置换术中能多大程度改善骨覆盖?
本研究评估4种后稳定型胫骨平台设计(3种对称型:NexGen、Attune、Vega;1种解剖型:Persona)在亚洲膝关节中的骨覆盖情况,测量后外侧、内侧后及内外侧区域未覆盖面积。解剖型设计在内侧后和内外侧维度的最佳匹配率分别为48%和42%,优于所有对称型设计(P < .05);后外侧维度最佳匹配率为76%,与对称型设计无显著差异(P > .05)。解剖型设计较对称型设计在内侧后覆盖改善约69.8%-74.3%。
要点
- 解剖型胫骨假体在内侧后和内外侧维度最佳匹配率分别为48%和42%,优于对称型设计(P < .05)。
- 后外侧维度最佳匹配率解剖型为76%,与对称型设计无显著差异(P > .05)。
- 对称型设计在内侧后(62%-78%)和内外侧(24%-34%)区域存在显著绝对覆盖不足。
核心结论
- 新近引入的解剖型胫骨设计改善了亚洲膝关节内侧后维度的表面覆盖。
- 与对称型设计相比,解剖型设计在内外侧匹配方面有小幅改善。
研究设计与样本
- 评估4种市售后稳定型胫骨平台设计(3种对称型:NexGen、Attune、Vega;1种解剖型:Persona)的骨覆盖情况。
- 测量后外侧、内侧后及内外侧三个区域的未覆盖面积。
- 假体尺寸根据假体外侧前后径与胫骨对应表面最匹配来选择。
- 覆盖不足<1 mm且覆盖过多<2 mm的膝关节被认为达到最佳匹配。
主要发现
- 解剖型设计在后外侧维度的最佳匹配率为76%,与对称型设计无显著差异(P > .05)。
- 解剖型设计在内侧后和内外侧维度的最佳匹配率分别为48%和42%,均优于所有对称型设计(P < .05)。
- 所有对称型胫骨设计在内侧后区域(62%-78%)和内外侧区域(24%-34%)存在显著绝对覆盖不足,组间无差异。
- 解剖型胫骨设计较对称型设计在内侧后覆盖改善约69.8%-74.3%。
关键数值与推荐
- 最佳匹配定义为覆盖不足<1 mm且覆盖过多<2 mm。
- 解剖型设计后外侧最佳匹配率76%,与对称型设计无显著差异(P > .05)。
- 解剖型设计内侧后最佳匹配率48%、内外侧最佳匹配率42%,均优于对称型设计(P < .05)。
- 对称型设计内侧后绝对覆盖不足62%-78%,内外侧绝对覆盖不足24%-34%。
- 解剖型设计较对称型设计内侧后覆盖改善约69.8%-74.3%。
临床怎么用
- 原文未据此给出推荐。
局限性
- 原文未报告局限性。
以上解读依据论文摘要(全文未开放获取或许可不允许翻译转载)。
原文
BACKGROUND: Recently, anatomical designs in total knee arthroplasty are introduced to address asymmetry of the resected tibia cutting surface. It is still not well known how much improvement would be achieved in total knee arthroplasty, especially in Asian knees. METHODS: We evaluated the bony coverage of 4 commercially available posterior-stabilized tibial designs (3 symmetrical: NexGen, Attune, and Vega; 1 anatomical: Persona) by measuring uncovered areas over 3 different regions: lateroposterior (LP), medioposterior (MP), and mediolateral (ML) areas. The implant size was chosen based on lateral anteroposterior dimension of the implant that most closely matched the corresponding surface of tibia. The knee with over coverage <1 mm and under coverage <2 mm was regarded as having optimal fit. RESULTS: The optimal fit of anatomical design in LP dimension was achieved in 76% of the cases, which was not significantly different from other symmetrical designs (P > .05). The anatomical tibial implant had a more optimal fit in MP and ML dimensions (48% and 42%, respectively) compared to all symmetric designs (P < .05). All symmetrical tibial designs had significant absolute underhang in MP (62%-78%) and ML (24%-34%) areas without difference. The anatomical tibial design had significant improvement for posteromedial coverage by about 69.8%-74.3% compared with the symmetrical designs. CONCLUSION: Recently introduced anatomical tibial design improves surface coverage at the medioposterior dimension in Asian knees. Moreover, there is small improvement in ML fit compared with the symmetrical designs.
引用
- Jin C, Song EK, Prakash J, et al. How Much Does the Anatomical Tibial Component Improve the Bony Coverage in Total Knee Arthroplasty? J Arthroplasty. 2016. PMID: 28109759. doi:10.1016/j.arth.2016.12.041
供执业医师工作参考,不替代临床判断;数值与分级以指南原文为准。