文献速递关节外科

髓腔锥形微槽是否影响全髋关节置换术中的锥形腐蚀:一项匹配队列回收研究

Do Stem Taper Microgrooves Influence Taper Corrosion in Total Hip Arthroplasty? A Matched Cohort Retrieval Study.
PubMed 文献 · J Arthroplasty · 2016-11-17

本研究采用匹配队列回收研究,纳入120对金属对聚乙烯轴承的头-柄配对,比较光滑与微槽柄锥的微动腐蚀损伤。结果显示,两组股骨头(P=.14)和柄锥(P=.35)的微动腐蚀损伤无差异,最大材料损失深度亦无差异(P=.71);结论不支持微槽柄锥表面在体内增加微动腐蚀损伤或材料释放的假设。

要点

  • 匹配队列回收研究纳入120对头-柄配对,光滑与微槽柄锥各60例。
  • 股骨头(P=.14)和柄锥(P=.35)的微动腐蚀损伤两组无差异。
  • 两组最大材料损失深度无差异(P=.71),微槽压印未见不同影响。

核心结论

  • 匹配队列回收研究结果不支持微槽柄锥表面在体内表现出增加微动腐蚀损伤或材料释放的假设。

研究设计与样本

  • 匹配队列回收研究,纳入120对来自金属对聚乙烯轴承的回收头-柄配对,控制植入时间、抗弯刚度、表观啮合长度和股骨头尺寸。
  • 分为2组,每组60个股骨头,分别与光滑或微槽柄锥配对。
  • 使用高精度圆度仪测量并分类表面形貌,采用Higgs-Goldberg评分法评估头-颈交界处微动腐蚀损伤。
  • 对14个损伤最重的股骨头分析最大材料损失深度,并进行聚焦离子束横截面观察氧化物和基底金属。

主要发现

  • 股骨头微动腐蚀损伤两组无差异(P=.14,Mann-Whitney检验)。
  • 柄锥微动腐蚀损伤两组无差异(P=.35)。
  • 两组最大材料损失深度无差异(P=.71)。
  • 横截面观察显示两组均存在接触损伤、微动迹象和富铬氧化物层。
  • 微槽压印对微动腐蚀行为未见不同影响。

关键数值与推荐

  • 股骨头微动腐蚀损伤组间比较P=.14(Mann-Whitney检验)。
  • 柄锥微动腐蚀损伤组间比较P=.35。
  • 最大材料损失深度组间比较P=.71。

局限性

  • 原文未报告局限性。

以上解读依据论文摘要(全文未开放获取或许可不允许翻译转载)。

原文

BACKGROUND: Previous studies identified imprinting of the stem morphology onto the interior head bore, leading researchers to hypothesize an influence of taper topography on mechanically assisted crevice corrosion. The purpose of this study was to analyze whether microgrooved stem tapers result in greater fretting corrosion damage than smooth stem tapers. METHODS: A matched cohort of 120 retrieved head-stem pairs from metal-on-polyethylene bearings was created controlling for implantation time, flexural rigidity, apparent length of engagement, and head size. There were 2 groups of 60 heads each, mated with either smooth or microgrooved stem tapers. A high-precision roundness machine was used to measure and categorize the surface morphology. Fretting corrosion damage at the head-neck junction was characterized using the Higgs-Goldberg scoring method. Fourteen of the most damaged heads were analyzed for the maximum depth of material loss and focused ion beam cross-sectioned to view oxide and base metal. RESULTS: Fretting corrosion damage was not different between the 2 cohorts at the femoral head (P = .14, Mann-Whitney) or stem tapers (P = .35). There was no difference in the maximum depths of material loss between the cohorts (P = .71). Cross-sectioning revealed contact damage, signs of micro-motion, and chromium-rich oxide layers in both cohorts. Microgroove imprinting did not appear to have a different effect on the fretting corrosion behavior. CONCLUSION: The results of this matched cohort retrieval study do not support the hypothesis that taper surfaces with microgrooved stems exhibit increased in vivo fretting corrosion damage or material release.

来源:J Arthroplasty,查看原文。版权归原作者所有。

引用

  1. Arnholt CM, MacDonald DW, Underwood RJ, et al. Do Stem Taper Microgrooves Influence Taper Corrosion in Total Hip Arthroplasty? A Matched Cohort Retrieval Study. J Arthroplasty. 2016. PMID: 28111124. doi:10.1016/j.arth.2016.11.018

供执业医师工作参考,不替代临床判断;数值与分级以指南原文为准。