手术入路决定全髋关节置换最佳轴承面配置:25年3万例分析
本研究基于单中心1998至2022年30,246例初次全髋关节置换,按手术入路和轴承面配置分层分析脱位风险。后路THA中双动假体降低脱位相对风险,前外侧入路中高边聚乙烯内衬脱位风险翻倍,直接前入路中轴承面配置无显著影响。结论不支持一刀切的轴承选择,应由手术入路指导。
要点
- 后路THA中双动假体降低脱位相对风险(RR<0.5,P<0.01),高危病例可考虑。
- 前外侧THA中高边聚乙烯内衬脱位相对风险翻倍(RR 2,P<0.01),平/中立内衬10年无脱位生存率99%。
- 直接前入路THA脱位风险最低,轴承面配置对脱位相对风险无显著影响。
核心结论
- 不支持对所有初次全髋关节置换采用一刀切的轴承面配置,手术入路应指导轴承选择。
研究设计与样本
- 回顾性队列研究,纳入单中心1998至2022年30,246例初次全髋关节置换,按手术入路和轴承面配置分层。
- 后路14,611髋(平/中立8,587、高边5,207、双动816),前外侧8,968髋(平/中立7,433、高边1,358、双动171),直接前入路6,667髋(平/中立6,541、高边91、双动35)。
- 平均年龄65岁(范围18至100),平均体重指数30(范围13至66),女性占52%,平均随访6年(范围2至26)。
主要发现
- 后路、前外侧、直接前入路THA的10年无脱位生存率分别为96%、98%、99%。
- 后路THA中双动假体降低脱位相对风险(RR<0.5,P<0.01)。
- 前外侧THA中平/中立聚乙烯内衬无脱位生存率99%,高边聚乙烯内衬脱位相对风险翻倍(RR 2,P<0.01)。
- 直接前入路THA中轴承面配置对脱位相对风险无显著影响。
临床怎么用
- 后路THA高危病例可考虑双动假体以降低脱位风险。
- 前外侧THA优先选择平/中立聚乙烯内衬,高边内衬脱位风险更高。
- 直接前入路THA轴承面配置选择对脱位风险影响不大。
以上解读依据论文摘要(全文未开放获取或许可不允许翻译转载)。
原文
INTRODUCTION: Dislocation remains a consequential complication following primary total hip arthroplasty (THA). Both surgical approach and bearing surface configuration individually influence dislocation risk. This study assessed the dislocation risk stratified by both surgical approach and bearing surface configuration to develop approach-specific recommendations for bearing selection. METHODS: We identified 30,246 primary THAs performed from 1998 to 2022 at a single academic institution. Hips were stratified by bearing surface configuration, including flat/neutral polyethylene (PE) liners, elevated rim/face-changing (elevated) PE liners, and dual-mobility (DM) constructs. There were 14,611 posterior hips (8,587 flat/neutral, 5,207 elevated, and 816 DM), 8,968 antero-lateral (AL, 7,433 flat/neutral, 1,358 elevated, and 171 DM), and 6,667 direct anterior (DA, 6,541 flat/neutral, 91 elevated, and 35 DM). The mean age was 65 years (range, 18 to 100), the mean body mass index was 30 (range, 13 to 66), and 52% were women. The mean follow-up was six years (range, two to 26). RESULTS: The survivorship free of dislocation at 10 years in the posterior, AL, and DA approach THAs were 96, 98, 99%, respectively. In posterior THAs, DM constructs reduced the relative risk of dislocation (RR [risk ratio] < 0.5, P < 0.01). In AL THAs, flat/neutral PE liners had a 99% survivorship free of dislocation, whereas elevated PE liners had double the relative risk of dislocation (RR 2, P < 0.01). In DA THAs, the bearing surface configuration had no discernible impact on the relative risk of dislocation. CONCLUSION: A one-size-fits-all approach to bearing surface configuration is not supported, and a surgical approach should guide bearing selection in primary THAs. For posterior approach THA, DM constructs should be considered in high-risk cases. For the AL approach THA, flat/neutral PE liners had the lowest absolute dislocation risk. Direct anterior THA had the lowest risk of dislocation risk, regardless of bearing selection.
引用
- Cochrane NH, Panos JA, Khela MS, et al. There Is No One-Size-Fits-All: Surgical Approach Dictates Optimal Bearing Surface Configuration Choice in 30,000 Total Hip Arthroplasties Over 25 Years. J Arthroplasty. 2026. PMID: 42767524. doi:10.1016/j.arth.2026.09.018
供执业医师工作参考,不替代临床判断;数值与分级以指南原文为准。