文献速递关节外科

机器人辅助与徒手UKA翻修全膝关节置换的比较分析:翻修部件使用、手术时间与费用

A Comparative Analysis of Robotic-Assisted and Manual Techniques for Unicondylar Knee Arthroplasty Conversion to Total Knee Arthroplasty: Revision Component Use, Surgical Time, and Cost.
PubMed 文献 · J Arthroplasty · 2026-07-28

单中心回顾性研究纳入2015至2025年62例UKA翻修TKA患者,其中35例(56.5%)采用机器人辅助。机器人辅助组使用更少翻修柄(11.4% vs 40.2%,P=0.02)和中度限制性聚乙烯(0 vs 14.8%,P=0.04),植入物费用更低(6149.79 vs 7185.42美元,P=0.02),手术时间更短(109.9 vs 123.0分钟,P=0.028)。

要点

  • 机器人辅助UKA翻修TKA可减少翻修柄使用(11.4% vs 40.2%,P=0.02)。
  • 机器人组未使用中度限制性聚乙烯,徒手组为14.8%(P=0.04)。
  • 机器人组植入物费用更低且手术时间更短,节省约490.6美元。

核心结论

  • 机器人辅助UKA翻修TKA与更少翻修柄、更少中度限制性聚乙烯及更低直接和间接费用相关。
  • 锥形套和垫块的使用在两组间无差异。
  • 结果可能支持机器人辅助以降低UKA翻修TKA的复杂性、费用和时间。

研究设计与样本

  • 经机构审查委员会批准的回顾性研究,纳入2015至2025年单中心连续接受UKA翻修TKA的患者。
  • 共识别62例UKA翻修TKA,其中35例(56.5%)使用机器人辅助。
  • 统计方法采用Fisher精确检验或卡方检验分析分类变量,Student t检验分析连续变量,显著性设为P<0.05。

主要发现

  • 机器人辅助组使用翻修柄的比例为11.4%,徒手组为40.2%(P=0.02)。
  • 机器人辅助组使用中度限制性聚乙烯的比例为0,徒手组为14.8%(P=0.04)。
  • 机器人辅助组植入物费用为6149.79美元,徒手组为7185.42美元(P=0.02),已包含一次性机器人费用。
  • 机器人辅助组手术时间为109.9分钟,徒手组为123.0分钟(P=0.028),机器人组额外节省490.6美元。
  • 锥形套或垫块的使用在两组间无差异。

临床怎么用

  • 对于UKA翻修TKA,可考虑机器人辅助以减少翻修柄使用和中度限制性聚乙烯的应用。
  • 机器人辅助可能缩短手术时间并降低植入物费用,但需结合一次性机器人成本综合评估。

局限性

  • 本研究为单中心回顾性研究,样本量较小(共62例)。
  • 未报告术后并发症的具体比较数据。

以上解读依据论文摘要(全文未开放获取或许可不允许翻译转载)。

原文

BACKGROUND: Unicondylar knee arthroplasty (UKA) conversion to total knee arthroplasty (TKA) is more complex than primary TKA, requiring additional time, effort, and occasionally revision components. Robotic assistance may alleviate the additional time and complexity when converting UKA to TKA. The aim of this study was to compare the use of revision components (e.g., stems, cones, and augments), polyethylene characteristics, time, and cost between manual versus robotic UKA conversion to TKA. METHODS: This is an institutional review board-approved, retrospective study of consecutive patients who underwent UKA conversion to TKA at a single institution from 2015 to 2025. Data extracted included surgical technique, reason for UKA failure, type of UKA and TKA implants, type of robot, use of revision components, polyethylene characteristics, surgical time, cost of implants, and postoperative complications. There were 62 UKA conversions to TKA identified, with 35 (56.5%) using robotic assistance. Statistical analyses were performed using Fisher's exact tests or Chi-square tests for categorical variables and Student's t-tests for continuous variables. Significance was set at P < 0.05. RESULTS: Robotic-assisted cases used fewer stems (11.4 versus 40.2%, P = 0.02) and less mid-level constrained polyethylene than manual cases (0 versus 14.8%, P = 0.04). Robotic conversion used significantly less costly implants than manual ($6,149.79 versus $7,185.42, P = 0.02), which included disposable robot costs. Robotic surgery resulted in shorter surgical time (109.9 versus 123.0 min, P = 0.028), reflecting an additional $490.6 in savings for the robotic group. CONCLUSIONS: Robotic-assisted UKA conversion to TKA was associated with fewer revision stems, less mid-level constraint, and lower direct and indirect costs. There was no difference in use of cones or augments. These results may support robotic assistance, reducing the complexity, cost, and time for UKA conversion to TKA.

来源:J Arthroplasty,查看原文。版权归原作者所有。

引用

  1. Aastroem KIM, Shah RP, Ferrara JAR, et al. A Comparative Analysis of Robotic-Assisted and Manual Techniques for Unicondylar Knee Arthroplasty Conversion to Total Knee Arthroplasty: Revision Component Use, Surgical Time, and Cost. J Arthroplasty. 2026. PMID: 42520995. doi:10.1016/j.arth.2026.07.034

供执业医师工作参考,不替代临床判断;数值与分级以指南原文为准。