文献速递关节外科

最大化轴承直径显著降低初次全髋关节置换术脱位率

The AAHKS Clinical Research Award: Maximizing Bearing Size Markedly Reduces Dislocations in Primary Total Hip Arthroplasty.
PubMed 文献 · J Arthroplasty · 2026-06-19

回顾性分析2016-2022年8607例固定轴承全髋关节置换术患者,比较最大化轴承直径(如48/50mm杯用36mm)与次大轴承的脱位风险。结果显示最大化轴承组无脱位(0/835),总体脱位率0.9%,多变量分析OR=0.14。

要点

  • 最大化轴承直径使脱位风险显著降低(OR=0.14),且该组无脱位发生。
  • 机器人手术、计算机导航、侧方及前方入路也显示保护作用。
  • 带唇边或偏移内衬与略高脱位风险相关,但后路亚组中内衬几何形状无影响。

核心结论

  • 在初次固定轴承全髋关节置换术中,完全最大化轴承直径可显著降低脱位风险,其效应量远超其他术者可控制变量。

研究设计与样本

  • 回顾性队列研究,纳入2016至2022年一家大型城市学术机构所有固定轴承全髋关节置换术患者,共8607例。

主要发现

  • 835例(9.8%)使用了最大化轴承直径,7309例(84.9%)使用次大轴承,总体脱位79例(0.9%)。
  • 最大化轴承直径组无脱位发生(P=0.003)。
  • 多变量分析中最大化轴承直径的OR=0.14;机器人手术OR=0.35,计算机导航OR=0.90,侧方入路OR=0.48,前方入路OR=0.62。
  • 带唇边内衬OR=1.2,偏移内衬OR=1.4,与略高脱位风险相关。
  • 后路入路使用非最大化轴承的4185例亚组中,内衬几何形状对脱位风险无影响。

关键数值与推荐

  • 最大化轴承直径定义:40/42mm杯用28mm,44/46mm杯用32mm,48/50mm杯用36mm,52/54/56mm杯用40mm。
  • 更大杯被排除因无相应更大轴承。

临床怎么用

  • 在固定轴承全髋关节置换术中,应优先选择可用的最大轴承直径以降低脱位风险。

局限性

  • 回顾性设计,仅纳入单一学术机构数据,更大尺寸杯被排除可能限制结论外推。

以上解读依据论文摘要(全文未开放获取或许可不允许翻译转载)。

原文

BACKGROUND: Modern polyethylene allows larger bearings in fixed-bearing total hip arthroplasty (THA), but any stability benefits of fully maximizing bearing diameter (e.g., 36-millimeter (mm) in 48/50-mm cups) are not well-established. We hypothesized that maximizing bearing diameter reduces odds of dislocation in primary fixed-bearing THA. METHODS: We retrospectively reviewed all patients who underwent fixed-bearing THA at a large, urban, academic institution between 2016 and 2022. We noted cases receiving the largest bearing available from any manufacturer for the acetabular diameter: 28 mm in 40/42 mm, 32 mm in 44/46-, 36- in 48/50-, or 40- in 52/54/56 mm. Larger cups were excluded because proportionately larger bearings were unavailable. Multivariate analyses using least-absolute-shrinkage-and-selection-operator logistic regression were performed to explore the association between maximized bearing diameter and dislocation risk while controlling for confounders. RESULTS: Bearing diameter was maximized in 835 (9.8%) of 8,607 patients, whereas 7,309 (84.9%) received the second-largest bearing available. There were 79 dislocations (0.9% overall); none occurred with maximized bearing diameters (P = 0.003). On univariate analyses, dislocation risk also varied with intraoperative technology use, surgical approach, and liner geometry (P = 0.017, P = 0.008, P = 0.007, respectively). In least-absolute-shrinkage-and-selection-operator regression including these variables, maximized bearing diameters heavily protected against dislocation (odds ratio (OR) = 0.14). Robotic surgery (OR = 0.35), computer-navigation (OR = 0.90), lateral (OR = 0.48), and anterior (OR = 0.62) approaches were also protective. Lipped (OR = 1.2) and offset (OR = 1.4) liners, commonly used with posterior approaches and nonmaximized bearing diameters, were associated with slightly higher odds of dislocation. Subanalysis of 4,185 patients who underwent posterior approach THA using nonmaximized bearings revealed that liner geometry did not impact dislocation odds within this subgroup. CONCLUSIONS: Fully maximizing bearing diameter markedly reduced dislocation odds in primary fixed-bearing THA. The magnitude of this effect was substantially larger compared to other variables under surgeon control.

来源:J Arthroplasty,查看原文。版权归原作者所有。

引用

  1. Wang E, McCormick K, Di Gangi C, et al. The AAHKS Clinical Research Award: Maximizing Bearing Size Markedly Reduces Dislocations in Primary Total Hip Arthroplasty. J Arthroplasty. 2026. PMID: 42320645. doi:10.1016/j.arth.2026.06.028

供执业医师工作参考,不替代临床判断;数值与分级以指南原文为准。