文献速递关节外科

后稳定型全膝关节置换术后胫骨柱骨折:疲劳 alone 是元凶吗?

Tibial Post Fracture in Posterior-Stabilized Total Knee Arthroplasty: Is Fatigue Alone the Culprit?
PubMed 文献 · J Arthroplasty · 2026-04-01

该回顾性研究分析6例患者7膝因后稳定型全膝关节置换(PS TKA)胫骨柱骨折行翻修,骨折平均术后12.8年,总体发生率0.22%。体外悬臂疲劳测试显示超高分子量聚乙烯(UHMWPE)和高交联聚乙烯(HXLPE)胫骨柱均能耐受生理性前后向疲劳载荷而不失败,提示单纯疲劳不足以解释临床骨折,磨损和几何设计优化更重要。

要点

  • PS TKA胫骨柱骨折罕见但严重,平均术后12.8年发生,总体发生率0.22%。
  • UHMWPE和HXLPE胫骨柱均能耐受生理性疲劳载荷,单纯疲劳不足以解释骨折。
  • 所有翻修假体均为倒角设计且存在柱基变窄的磨损迹象,减少磨损和优化几何设计是关键。

核心结论

  • UHMWPE和HXLPE胫骨柱均能耐受生理性前后向疲劳而不失败,单纯疲劳不足以解释临床胫骨柱骨折。
  • 减少磨损和优化胫骨柱几何设计是预防PS TKA晚期胫骨柱骨折的关键。

研究设计与样本

  • 回顾性分析6例患者7膝因PS TKA胫骨柱骨折行翻修的 demographics、假体和手术因素。
  • 体外悬臂疲劳测试使用UHMWPE和HXLPE制成的PS TKA胫骨衬垫,通过替代股骨部件在0°和75°屈曲施加往复前后向载荷,无轴向压缩。
  • 测试两种胫骨柱设计:倒角柱和近端横截面更大的非倒角柱;以2 Hz循环加载,从±209 N开始10,000周期,每10,000周期逐步增加,并在生理和超生理载荷下持续测试至10百万周期(Mc)。

主要发现

  • 骨折发生于术后平均12.8年(范围4.5至17.8年),总体发生率为0.22%。
  • 5例骨折使用UHMWPE衬垫,2例使用HXLPE衬垫;所有取出的部件均为倒角设计并显示与磨损一致的柱基变窄。
  • 测试中两种胫骨柱设计在载荷超过1,254 N时均在超过63,000周期后失败,该载荷高于生理性前后向力。
  • 非倒角设计在大于1,254 N载荷下承受10 Mc,而倒角设计在627 N下承受10 Mc。

关键数值与推荐

  • 骨折平均术后时间12.8年(范围4.5至17.8年),总体发生率0.22%。
  • 疲劳测试起始载荷±209 N持续10,000周期,每10,000周期逐步增加,2 Hz频率。
  • 两种设计在载荷超过1,254 N时均在超过63,000周期后失败。
  • 非倒角设计承受大于1,254 N达10 Mc,倒角设计承受627 N达10 Mc。

临床怎么用

  • 临床遇到PS TKA晚期胫骨柱骨折时,应考虑磨损和几何设计因素而非单纯疲劳。
  • 选择胫骨柱设计时优先考虑减少磨损和优化几何形状(如非倒角设计可能更耐疲劳)。

局限性

  • 回顾性研究样本量小(6例患者7膝),可能限制普遍性。
  • 体外疲劳测试未模拟轴向压缩,且测试条件可能与体内实际载荷存在差异。

以上解读依据论文摘要(全文未开放获取或许可不允许翻译转载)。

原文

BACKGROUND: Tibial post fracture in posterior-stabilized total knee arthroplasty (PS TKA) is a rare but serious complication resulting from insufficient post strength and polyethylene wear. Although highly cross-linked polyethylene (HXLPE) reduces wear compared to ultra-high-molecular weight polyethylene (UHMWPE), its mechanical strength is not improved. This study reports a series of tibial post fractures and evaluates whether fatigue alone accounts for such failures. METHODS: There were six patients (seven knees) who underwent revision for tibial post fractures reviewed retrospectively for demographic, implant, and surgical factors. Complementary cantilever fatigue tests were conducted using PS TKA tibial inserts fabricated from UHMWPE and HXLPE. Reversing antero-posterior (AP) loads were applied via surrogate femoral components at 0° and 75° flexion, without axial compression. There were two post designs tested: a chamfered post and a nonchamfered post with a larger proximal cross-section. Cyclic loading at two Hz began at ± 209 N for 10,000 cycles, with stepwise increase every 10,000 cycles. Additional tests at physiological and supraphysiological loads continued for up to 10 million cycles (Mc), simulating decades of in vivo use. RESULTS: Fractures occurred a mean of 12.8 years postoperatively (range, 4.5 to 17.8). There were five fractures that had UHMWPE and two that had HXLPE inserts. The overall incidence was 0.22%. All retrieved components were chamfered and exhibited post-base narrowing consistent with wear. In testing, both post designs failed after more than 63,000 cycles at loads exceeding 1,254 N, above physiological AP forces. The nonchamfered design withstood greater than 1,254 N for 10 Mc, while the chamfered design endured 627 N for 10 Mc. CONCLUSIONS: Both UHMWPE and HXLPE posts withstood physiological AP fatigue without failure, indicating that fatigue alone was insufficient to explain clinical fractures. Minimizing wear and optimizing post geometry are critical to preventing late tibial post fracture in PS TKA.

来源:J Arthroplasty,查看原文。版权归原作者所有。

引用

  1. Garvin KL, Zitsch B, Weisenburger J, et al. Tibial Post Fracture in Posterior-Stabilized Total Knee Arthroplasty: Is Fatigue Alone the Culprit? J Arthroplasty. 2026. PMID: 41956871. doi:10.1016/j.arth.2026.03.015

供执业医师工作参考,不替代临床判断;数值与分级以指南原文为准。