半月板缝合间距应≤7 mm:一项生物力学研究
在50个牛半月板纵向撕裂模型上,采用垂直褥式由内向外技术以2-0编织缝线修复,测试3、5、7、9、11 mm五种缝合间距。结果显示间距≤7 mm的间隙形成较9和11 mm平均少36%,构建刚度更高;作者建议纵向撕裂垂直褥式修复时间距≤7 mm。
要点
- 缝合间距≤7 mm的间隙形成较9和11 mm平均少36%。
- 间距≤7 mm的构建刚度显著高于≥9 mm(所有P<.05)。
- 3、5、7 mm间距间间隙形成与刚度无显著差异。
核心结论
- 半月板修复缝合间距≤7 mm在循环加载下间隙形成显著低于>7 mm且构建刚度更高。
- 基于此生物力学数据,纵向撕裂垂直褥式修复可考虑≤7 mm缝合间距。
研究设计与样本
- 研究为控制实验室研究,使用50个牛半月板制作完整垂直周向撕裂。
- 所有病变以两根2-0编织缝线采用垂直褥式由内向外技术修复。
- 测试3、5、7、9、11 mm五种缝合间距,每组10个样本。
主要发现
- 3、5、7 mm间距的间隙形成较9和11 mm平均少36%,差异有统计学意义。
- 3、5、7 mm间距之间间隙形成无显著差异。
- 7 mm及以下间距的构建刚度显著高于≥9 mm(所有P<.05)。
- 3、5、7 mm间距之间构建刚度无显著差异。
- 失败模式为缝线断裂76%(38/50)、缝线切割22%(11/50)、两者兼有2%(1/50),失败模式与缝合间距无关。
关键数值与推荐
- 每个样本经历1000次循环加载,载荷5至20 N(复合载荷),横梁速度75 mm/min,随后行加载至失败测试。
- 使用数字图像相关系统与2台高速相机在10、100、500、1000次循环后测量两缝线间撕裂开口间隙。
- 统计学采用单因素方差分析及Bonferroni校正事后t检验,显著性设为P<.05。
临床怎么用
- 纵向半月板撕裂行垂直褥式修复时,可考虑将缝合间距控制在≤7 mm以减小循环加载下间隙形成并提高构建刚度。
局限性
- 研究为牛半月板离体生物力学实验,非人体临床研究。
以上解读依据论文摘要(全文未开放获取或许可不允许翻译转载)。
原文
BACKGROUND: The resistance to gap development under repetitive loading influences the probability of meniscal healing after meniscal repair. The optimal meniscal suture interval spacing for repairing longitudinal meniscal tears is poorly understood. This study aimed to investigate the effect of varying suture interval spacings on the biomechanical properties of vertical meniscal repairs. HYPOTHESIS: There is a critical meniscal suture interval spacing beyond which the gap development during cycling loading increases and the stiffness of the construct decreases. STUDY DESIGN: Controlled laboratory study. METHODS: In 50 bovine menisci, complete vertical circumferential meniscal tears were created. All lesions were repaired using two 2-0 braided sutures with the vertical mattress inside-out technique. Five suture spacings (3, 5, 7, 9, and 11 mm) with 10 samples each were tested. Each sample underwent 1000 loading cycles between 5 and 20 N (combined load) at a 75-mm/min crosshead speed and subsequent load-to-failure testing. The tear opening gap between the 2 meniscal sutures was measured using the Digital Image Correlation system with 2 high-speed cameras after 10, 100, 500, and 1000 cycles. Gap formation, cyclic stiffness, and failure modes were measured. A 1-way analysis of variance with post hoc t testing with Bonferroni correction for significant pairwise analysis of all outcome variables was performed. Statistical significance was set at a P value <.05. RESULTS: Meniscal repairs with suture interval spacings of 3 mm, 5 mm, and 7 mm demonstrated statistically significantly smaller gap formation-a mean of 36% less-compared with spacings of 9 mm and 11 mm. There were no significant differences in gap formation between the suture interval spacings of 3 mm, 5 mm, and 7 mm. Construct stiffness was significantly higher with a suture interval spacing of 7 mm and less compared with ≥9 mm (all P < .05). No significant differences in construct stiffness were observed among the 3-mm, 5-mm, and 7-mm suture intervals. Suture breakage occurred in 76% of cases (38/50), suture cut-through in 22% (11/50), and a combination of both in 2% (1/50). Failure mode did not correlate with suture distance. CONCLUSION: Meniscal repair with a suture interval spacing of ≤7 mm demonstrates significantly lower gap formation and higher construct stiffness during cyclic loading than interval spacings of >7 mm. Based on these biomechanical data, surgeons should consider a ≤7-mm suture interval spacing for vertical mattress meniscal repair of longitudinal tears. CLINICAL RELEVANCE: On the basis of this biomechanical data, surgeons should consider a ≤7-mm suture interval spacing for vertical mattress meniscal repair of longitudinal tears.
引用
- Runer A, Höger SA, Frantz J, et al. Suture Interval Spacing in Meniscal Repair-Aim for ≤7 mm: A Biomechanical Study: ISAKOS Albert Trillat Award 2025. Am J Sports Med. 2026. PMID: 41673827. doi:10.1177/03635465251411932
供执业医师工作参考,不替代临床判断;数值与分级以指南原文为准。