文献速递关节外科

高交联聚乙烯制造特性对全髋关节置换术后股骨头侵入的影响:10至22年随访研究

Influence of highly cross-linked polyethylene manufacturing characteristics on femoral head penetration in total hip arthroplasty : a ten- to 22-year follow-up study.
PubMed 文献 · Bone Joint J · 2025-05-01

单机构研究纳入2001年1月至2013年12月904例使用高交联聚乙烯内衬的非骨水泥全髋关节置换,746髋随访至少10年,比较七种内衬的股骨头线性侵入率。各内衬组10年总侵入均值0.14至0.20毫米(p=0.649),无因磨损或骨溶解翻修,无影像学骨溶解;髋臼外倾角>50°者1至15年总侵入0.21毫米,35°至50°者0.10毫米(p<0.001)。

要点

  • 七种高交联聚乙烯内衬10年股骨头总侵入均值0.14至0.20毫米,组间无显著差异(p=0.649)。
  • 10年时27髋(3.6%)股骨头侵入>0.40毫米,无因磨损或骨溶解翻修。
  • 髋臼外倾角>50°者1至15年总侵入0.21毫米,35°至50°者0.10毫米(p<0.001)。

核心结论

  • 高交联聚乙烯制造特性可导致全髋关节置换患者磨损性能不同,但平均随访15年时各组临床和影像学结果均优良。
  • 髋臼假体位置可影响现代高交联聚乙烯的股骨头侵入。

研究设计与样本

  • 单机构研究,2001年1月至2013年12月共施行904例使用高交联聚乙烯内衬的非骨水泥全髋关节置换。
  • 识别七种高交联聚乙烯内衬:重熔型3种、退火型2种、顺序退火型1种、维生素E扩散型1种。
  • 746髋获得至少10年随访,于术后6周及1、5、10、15年测量线性股骨头侵入率。
  • 采用Dorr标准对数字化X线片测量,使用Roman v.1 70软件包分析。

主要发现

  • 无患者因磨损或骨溶解接受翻修。
  • 全髋关节置换术后10年所有组股骨头总侵入均值范围为0.14毫米(SD 0.06)至0.20毫米(SD 0.17)(p=0.649)。
  • 10年时股骨头侵入>0.40毫米者27髋(3.6%)。
  • 术后1至15年,髋臼外倾角>50°的假体平均总侵入0.21毫米(SD 0.13),置于35°至50°者0.10毫米(SD 0.12)(p<0.001)。
  • 影像学分析未检测到任何髋骨溶解。

局限性

  • 原文未报告局限性。

以上解读依据论文摘要(全文未开放获取或许可不允许翻译转载)。

原文

AIMS: Highly cross-linked polyethylene (HXLPE) has reduced wear and revision rates in total hip arthroplasty (THA) in the long term. However, the effect of HXLPE manufacturing characteristics on femoral head penetration has not yet been clearly defined. We report this single-institution study to investigate the clinical and radiological results of various HXLPE liners in THA. METHODS: Between January 2001 and December 2013, 904 uncemented THAs using HXLPE liners were performed at our institution. Seven different HXLPE liner types were identified: remelted (n = 3), annealed (n = 2), sequentially annealed (n = 1), and vitamin E diffused (n = 1). A total of 746 hips were available for a minimum follow-up of ten years. The linear femoral head penetration rate was measured at six weeks and at one, five, ten, and 15 years, applying the Dorr criteria to digitized radiographs, using the Roman v. 1 70 software package for analysis. RESULTS: No patient was revised due to wear or osteolysis. The mean total femoral head penetration ten years after THA ranged from 0.14 mm (SD 0.06) to 0.20 mm (SD 0.17) for all groups (p = 0.649). Femoral head penetration > 0.40 mm at ten years was observed in 27 (3.6%) hips. From one to 15 years after surgery, mean total penetration was 0.21 mm (SD 0.13) in components with an acetabular inclination > 50° and 0.10 mm (SD 0.12) in those placed between 35° and 50° (p < 0.001). The radiological analysis did not detect osteolysis in any hip. CONCLUSION: Although HXLPE characteristics can result in different wear performance in patients undergoing THA at a mean follow-up of 15 years, the clinical and radiological results were excellent in all groups. The position of the acetabular component can influence the femoral head penetration of modern HXLPEs.

来源:Bone Joint J,查看原文。版权归原作者所有。

引用

  1. García-Rey E, Saldaña L. Influence of highly cross-linked polyethylene manufacturing characteristics on femoral head penetration in total hip arthroplasty : a ten- to 22-year follow-up study. Bone Joint J. 2025. PMID: 40306664. doi:10.1302/0301-620X.107B5.BJJ-2024-1083.R1

供执业医师工作参考,不替代临床判断;数值与分级以指南原文为准。