文献速递关节外科

一种高效工作流程方法用于负重三维膝关节运动学术前与术后评估

A Workflow-Efficient Approach to Pre- and Post-Operative Assessment of Weight-Bearing Three-Dimensional Knee Kinematics.
PubMed 文献 · J Arthroplasty · 2025-02-06

该文介绍一种利用机器学习增强软件和升级C臂透视的临床实用方法,可在十分钟内由一名放射技师完成负重膝关节三维运动学测量,用于全膝关节置换术(TKA)术前规划和术后评估。作者认为该方法可使动态三维膝关节运动学成为病变或置换后膝关节常规临床检查的组成部分。

要点

  • 使用升级探测器和软件的普通C臂,进行8秒水平扫掠脉冲透视扫描负重膝关节。
  • 患者膝关节在站立、跪、蹲、上下楼梯、椅子及步态活动中接受脉冲C臂透视成像。
  • 采用有限弧锥束重建方法创建含植入物的股骨和胫骨/腓骨三维模型,用于模型-图像配准以量化三维膝关节运动学。

核心结论

  • 负重运动学影响TKA术前和术后的膝关节功能。
  • 作者提出一种利用普通但数字化升级的成像硬件和软件的方法,实现高效检查方案以准确评估三维膝关节运动学。
  • 借助这些能力,将有可能把动态三维膝关节运动学作为病变或置换后膝关节患者常规临床检查的组成部分。

研究设计与样本

  • 方法学描述:使用带升级探测器和软件的普通C臂,对负重膝关节进行8秒水平扫掠脉冲透视扫描。
  • 患者在站立、跪、蹲、上下楼梯、椅子及步态活动中接受脉冲C臂透视成像。
  • 采用有限弧锥束重建方法创建含植入物的股骨和胫骨/腓骨三维模型,进行模型-图像配准以量化三维膝关节运动学。

主要发现

  • 所提出的方案可由一名放射技师在十分钟内完成。
  • 除台阶和凳子外,无需额外设备。
  • 图像分析可在升级C臂机载计算机或云端进行,之后将检查结果载入图像归档与通信系统及电子病历系统。

临床怎么用

  • 作者认为,借助这些能力,将有可能把动态三维膝关节运动学作为病变或置换后膝关节患者常规临床检查的组成部分。

局限性

  • 原文未报告局限性

以上解读依据论文摘要(全文未开放获取或许可不允许翻译转载)。

原文

BACKGROUND: Knee kinematics during daily activities reflect disease severity preoperatively and are associated with clinical outcomes after total knee arthroplasty (TKA). It is widely believed that measured kinematics would be useful for preoperative planning and postoperative assessment. Despite decades-long interest in measuring three-dimensional (3D) knee kinematics, no methods are available for routine, practical clinical examinations. We report a clinically practical method utilizing machine-learning-enhanced software and upgraded C-arm fluoroscopy for the accurate and time-efficient measurement of pre-TKA and post-TKA 3D dynamic knee kinematics. METHODS: Using a common C-arm with an upgraded detector and software, we performed an 8-s horizontal sweeping pulsed fluoroscopic scan of the weight-bearing knee joint. The patient's knee was then imaged using pulsed C-arm fluoroscopy while performing standing, kneeling, squatting, stair, chair, and gait motion activities. We used limited-arc cone-beam reconstruction methods to create 3D models of the femur and tibia/fibula bones with implants, which can then be used to perform model-image registration to quantify the 3D knee kinematics. RESULTS: The proposed protocol can be accomplished by an individual radiology technician in ten minutes and does not require additional equipment beyond a step and stool. The image analysis can be performed by a computer onboard the upgraded c-arm or in the cloud, before loading the examination results into the Picture Archiving and Communication System and Electronic Medical Record systems. CONCLUSIONS: Weight-bearing kinematics affects knee function pre- and post-TKA. It has long been exclusively the domain of researchers to make such measurements. We present an approach that leverages common, but digitally upgraded, imaging hardware and software to implement an efficient examination protocol for accurately assessing 3D knee kinematics. With these capabilities, it will be possible to include dynamic 3D knee kinematics as a component of the routine clinical workup for patients who have diseased or replaced knees.

来源:J Arthroplasty,查看原文。版权归原作者所有。

引用

  1. Banks SA, Yildirim G, Jachode G, et al. A Workflow-Efficient Approach to Pre- and Post-Operative Assessment of Weight-Bearing Three-Dimensional Knee Kinematics. J Arthroplasty. 2025. PMID: 39921117. doi:10.1016/j.arth.2025.01.050

供执业医师工作参考,不替代临床判断;数值与分级以指南原文为准。