文献速递关节外科

在无影像导航机器人平台的全膝关节置换术中定义膝关节冠状面排列表型的独特应力曲线形态

Defining Distinct Stress Curve Morphologies for Coronal Plane Alignment of the Knee Phenotypes Using an Imageless Navigation Robotic Platform in Total Knee Arthroplasty.
PubMed 文献 · J Arthroplasty · 2024-06-13

研究纳入来自2套无影像机器人辅助导航系统、使用后稳定型假体的1112例全膝关节置换病例,按膝关节冠状面排列(CPAK)分型归类,测量整个屈伸弧度的内外侧初始间隙并生成间隙曲线形态。结果显示CPAK I至VI型各具独特的间隙曲线形态和内外侧间隙平衡行为,可为表型特异性治疗提供「指纹」依据。

要点

  • CPAK I型内外侧间隙差最大(-3.6至-2.1),内侧间室在伸直位最紧。
  • CPAK III型伸直位内侧松、外侧紧,深屈曲时反转为内侧紧(2.1至-0.8)。
  • 各CPAK表型具有独特应力曲线,可辅助制定表型特异性平衡策略。

核心结论

  • 各CPAK表型具有独特的应力曲线和内外侧间隙行为,构成对应表型的「指纹」。
  • 研究这些形态有助于确定最佳的表型特异性治疗,包括对线策略、假体选择和间隙平衡,以获得最佳功能和患者结局。

研究设计与样本

  • 研究纳入来自2套无影像机器人辅助导航系统、使用后稳定型假体的1112例全膝关节置换病例,按CPAK表型分类。
  • 测量整个膝关节屈伸弧度的内外侧初始间隙值,生成间隙曲线形态,并计算各表型的内外侧间隙平衡;本研究纳入最常见的CPAK I至VI型。

主要发现

  • CPAK I型维持最大的内外侧间隙差(-3.6至-2.1),内侧间室在伸直位最紧。
  • CPAK II型外侧间室相对内侧间隙松弛(-1.0至-1.9),内侧间室随屈曲逐渐收紧。
  • CPAK III型伸直位内侧较松、外侧较紧,深屈曲时反转为内侧较紧(2.1至-0.8)。
  • CPAK IV型间室差异随屈曲增加而减小(-3.7至0.6)。
  • CPAK V型紧张度波动(-0.6至1.8),CPAK VI型内侧间室随屈曲收紧更明显(0.6至1.8)。

局限性

  • 原文未报告局限性。

以上解读依据论文摘要(全文未开放获取或许可不允许翻译转载)。

原文

BACKGROUND: The coronal plane alignment of the knee (CPAK) classification system divides coronal knee anatomy into 9 phenotypes, suggesting different soft tissue balancing is needed for optimal outcomes. We investigated the interplay between CPAK phenotypes and gap stress curves throughout the knee's range of motion, aiming to understand their impact on total knee arthroplasty balancing. METHODS: There were 1,112 total knee arthroplasty cases from 2 imageless robotic assisted navigation systems using posterior stabilized implants that were classified into CPAK phenotypes. Medial and lateral initial gap values were measured throughout the knee flexion-extension arc, gap curve morphologies were generated, and mediolateral (ML) gap balance was calculated for each phenotype. The most common phenotypes were included in this study, CPAK I to VI. RESULTS: Each phenotype exhibited a distinct gap curve morphology. Type I maintained the largest ML gap difference (-3.6 to -2.1), with the medial compartment tightest in extension. Type II showed relative laxity in the lateral compartment compared to the medial gap (-1.0 to -1.9), with the medial compartment tightening through flexion. Type III had a looser medial and tighter lateral compartment in extension that inverts to a tighter medial compartment in deep flexion (2.1 to -0.8), while Type IV showed a decreasing compartment difference with increased flexion (-3.7 to 0.6). Type V had fluctuating tightness (-0.6 to 1.8), and Type VI had the medial compartment tightening more with flexion (0.6 to 1.8). CONCLUSIONS: The distinct stress curves and ML gap behavior provide a "fingerprint" for each corresponding CPAK phenotype. Investigating these morphologies can help determine the best phenotype-specific treatments, including alignment strategy, implant selection, and gap balance, for optimal functional and patient outcomes.

来源:J Arthroplasty,查看原文。版权归原作者所有。

引用

  1. Holland CT, Savov P, Ettinger M, et al. Defining Distinct Stress Curve Morphologies for Coronal Plane Alignment of the Knee Phenotypes Using an Imageless Navigation Robotic Platform in Total Knee Arthroplasty. J Arthroplasty. 2024. PMID: 38879091. doi:10.1016/j.arth.2024.06.011

供执业医师工作参考,不替代临床判断;数值与分级以指南原文为准。