自动化撞击能否改善全髋关节置换术中的股骨假体型号选择与对线?
该回顾性研究纳入2017至2021年由单一关节置换外科医生完成的184例初次全髋关节置换术患者,比较自动化撞击(122例)与手动锤击撞击(62例)在股骨假体型号选择、髓腔填充比(CFR)和冠状面对线上的差异。自动化组使用更大的股骨柄、近端股骨四个层面的CFR均更大、冠状面对线更外翻且更可靠、手术时间更短,两组均无术中或术后假体周围骨折。
要点
- 自动化撞击组股骨柄型号更大(5.67 vs 4.82,P = .006),近端股骨四个层面CFR均更大(P = .004)。
- 自动化撞击组冠状面对线更外翻且更可靠(-0.57(SD 1.50)vs -0.03(SD 2.17)度,P = .03),手术时间更短(平均78 vs 90分钟,P < .001)。
- 两组均无术中或术后假体周围骨折。
核心结论
- 自动化撞击是初次全髋关节置换术中股骨准备的一种安全技术,可改善股骨柄冠状面对线、优化近端股骨髓腔填充并缩短手术时间。
研究设计与样本
- 回顾性分析2017至2021年由单一关节置换外科医生完成的184例初次全髋关节置换术,使用现代非骨水泥股骨假体,采用直接前入路或后外侧入路。
- 最终队列按扩髓时撞击技术分为自动化组(N = 122)和手动组(N = 62),并使用倾向性评分匹配年龄、体重指数、性别、高偏距与标准偏距股骨柄及术前股骨骨质量。
- 通过影像学回顾测量髓腔内假体CFR和冠状面对线。
主要发现
- 自动化组趋向于使用更大的股骨柄(5.67 vs 4.82,P = .006)。
- 自动化组在近端股骨全部4个层面的CFR均更大(P = .004)。
- 自动化组冠状面对线更外翻且更可靠(-0.57(SD 1.50)vs -0.03(SD 2.17)度,P = .03)。
- 自动化组手术时间显著更短(平均78 vs 90分钟,P < .001)。
- 两组均无术中或术后假体周围骨折。
局限性
- 原文未报告局限性。
以上解读依据论文摘要(全文未开放获取或许可不允许翻译转载)。
原文
BACKGROUND: While automated impaction can provide a more standardized process for femoral canal preparation, little is known regarding its effect on femoral component sizing and position. The purpose of our study was to directly compare femoral component canal fill ratio (CFR) and coronal alignment between primary total hip arthroplasty (THA) procedures performed with automated impaction versus manual mallet impaction. METHODS: A retrospective analysis was performed on 184 patients who underwent primary THA by a single arthroplasty surgeon between 2017 and 2021 with a modern cementless femoral component using either the direct anterior or posterolateral approach. The final cohort was divided into 2 groups based on impaction technique during broaching: automated (N = 122) or manual (N = 62). A propensity score match was used to match for age, body mass index, sex, high versus standard offset stem, and preoperative femoral bone quality. Radiographic review was performed to measure intramedullary prosthetic CFR and coronal alignment. RESULTS: The automated cohort trended toward the use of a larger stem (5.67 versus 4.82, P = .006) and had a larger CFR at all 4 levels within the proximal femur (P = .004). The automated cohort had a more valgus and reliable coronal alignment (-0.57 (SD 1.50) versus -0.03 (SD 2.17) degrees, P = .03) and significantly shorter operative time (mean 78 versus 90 minutes, P < .001). There were no intraoperative or postoperative periprosthetic fractures in either cohort. CONCLUSION: Automated impaction in primary THA is a safe technique for femoral preparation, which resulted in improved stem coronal alignment, optimized canal fill within the proximal femur, and reduced operative times.
引用
- Thalody HS, Post ZD, Bridges TN, et al. Does Automated Impaction Improve Femoral Component Sizing and Alignment in Total Hip Arthroplasty? J Arthroplasty. 2023. PMID: 37146701. doi:10.1016/j.arth.2023.04.054
供执业医师工作参考,不替代临床判断;数值与分级以指南原文为准。