中级别限制性垫片可减少后稳定型全膝关节置换术中关节线抬高导致的耦合轴向旋转,但不减少冠状面屈曲中期松弛:一项计算研究
研究采用6个计算膝关节模型,模拟后稳定型全膝关节置换术中股骨远端额外切除+2 mm和+4 mm导致关节线抬高,比较中级别限制性垫片与后稳定型垫片在30°、45°、60°屈曲时的冠状面松弛和耦合轴向旋转;结论为中级别限制性垫片大幅减少耦合轴向旋转,但对冠状面松弛影响很小。
要点
- 在30°屈曲、股骨远端+2 mm和+4 mm切除时,中级别限制性垫片使耦合轴向旋转分别减少5.6°(P=0.01)和7.1°(P=0.02)。
- 在30°屈曲、股骨远端+2 mm和+4 mm切除时,中级别限制性垫片使冠状面松弛分别减少0.8°(P=0.06)和1.0°(P=0.07),未达统计学显著。
- 作者认为应努力避免初次全膝关节置换术中的关节线抬高,因为即使是中级别限制性垫片也可能无法减轻冠状面松弛。
核心结论
- 在为缓解屈曲挛缩而额外行股骨远端切除时,与后稳定型垫片相比,使用中级别限制性垫片大幅减少耦合轴向旋转,但对冠状面松弛影响很小。
- 作者认为应努力避免初次全膝关节置换术中的关节线抬高,因为即使是中级别限制性垫片也可能无法减轻冠状面松弛。
研究设计与样本
- 研究基于计算机断层扫描和平均软组织特性建立6个计算膝关节模型,模型具有平衡的伸直间隙但存在10°屈曲挛缩。
- 模拟股骨远端+2 mm和+4 mm切除,分别使用后稳定型垫片和中级别限制性垫片,在30°、45°、60°屈曲时施加±10 Nm内外翻力矩。
- 测量并比较两种垫片模型的冠状面松弛(内外翻角度之和)和耦合轴向旋转(内旋与外旋之和)。
主要发现
- 在30°屈曲、+2 mm切除时,后稳定型垫片的冠状面松弛平均为7.9°±0.6°,中级别限制性垫片减少0.8°(P=0.06)。
- 在30°屈曲、+4 mm切除时,后稳定型垫片的冠状面松弛平均为11.3°±0.6°,中级别限制性垫片减少1.0°(P=0.07)。
- 在30°屈曲、+2 mm切除时,后稳定型垫片的旋转松弛平均为11.1°±3.9°,中级别限制性垫片减少5.6°(P=0.01)。
- 在30°屈曲、+4 mm切除时,后稳定型垫片的旋转松弛平均为12.5°±4.6°,中级别限制性垫片减少7.1°(P=0.02)。
- 在45°和60°屈曲时观察到相似的模式。
临床怎么用
- 作者认为应努力避免初次全膝关节置换术中的关节线抬高,因为即使是中级别限制性垫片也可能无法减轻冠状面松弛。
局限性
- 原文未报告局限性。
以上解读依据论文摘要(全文未开放获取或许可不允许翻译转载)。
原文
BACKGROUND: Surgeons may resect additional distal femur during primary posterior-stabilized (PS) total knee arthroplasty (TKA) to correct a flexion contracture. However, the resultant joint line elevation (JLE) increases mid-flexion laxity. We determined whether a mid-level constraint (MLC) insert reduced mid-flexion laxity after JLE. METHODS: Six computational knee models were developed using computed tomography scans and average soft tissue properties yielding balanced extension gaps but with a 10° flexion contracture. Distal femoral resections of +2 and +4 mm were simulated with PS and MLC inserts. Varus-valgus ±10 Nm moments were applied at 30°, 45°, and 60° of flexion. Coronal laxity (the sum of varus-valgus angulation) and coupled axial rotation (the sum of internal/external rotation) were measured and compared between insert models. RESULTS: At 30° of flexion, coronal laxities with the PS insert at the +2 and +4 mm resections averaged 7.9° ± 0.6° and 11.3° ± 0.6°, respectively, and decreased by 0.8° (P = .06) and 1.0° (P = .07), respectively, with the MLC insert. PS rotational laxities at the +2 and +4 mm resections averaged 11.1° ± 3.9° and 12.5° ± 4.6°, respectively, and decreased by 5.6° (P = .01) and 7.1° (P = .02), respectively, with the MLC insert. Similar patterns were observed at 45° and 60° of flexion. CONCLUSION: With additional distal femoral resections to alleviate a flexion contracture, utilizing an MLC insert substantially reduced coupled axial rotation but had a minimal impact on coronal laxity compared to a PS insert. Efforts should be taken to avoid JLE in primary total knee arthroplasty as even MLC inserts may not mitigate coronal laxity.
引用
- Elmasry SS, Kahlenberg CA, Mayman DJ, et al. A Mid-Level Constrained Insert Reduces Coupled Axial Rotation but Not Coronal Mid-Flexion Laxity Induced by Joint Line Elevation in Posterior-Stabilized Total Knee Arthroplasty: A Computational Study. J Arthroplasty. 2022. PMID: 35240279. doi:10.1016/j.arth.2022.02.089
供执业医师工作参考,不替代临床判断;数值与分级以指南原文为准。