文献速递关节外科

采用卡尺法运动学对线技术行全膝关节置换术后的对线与平衡如何

What Is the Alignment and Balance of a Total Knee Arthroplasty Performed Using a Calipered Kinematic Alignment Technique?
PubMed 文献 · J Arthroplasty · 2022-02-18

研究利用607例连续机器人辅助全膝关节置换术的动态韧带张力数据,模拟卡尺法运动学对线全膝关节置换术(cKATKA),计算胫骨近端截骨以实现伸膝间隙平衡,并模拟对称后髁截骨计算屈膝间隙平衡所需的胫骨截骨。结果显示术前内翻畸形越重,实现伸膝间隙平衡所需的胫骨内翻截骨越大(P < .0001),胫骨内翻角度与屈膝间隙平衡无相关性(P > .1);轻度内翻膝分别有81%和95%可在距机械轴3°和5°内实现平衡,中重度内翻膝仅37%和74%可在上述边界内平衡(P < .01),总体上95%的模拟膝关节可在0° ± 5°内实现平衡,但50%的模拟全膝关节置换术在屈膝时内侧间隙较外侧间隙更松。

要点

  • 术前内翻畸形越重,实现伸膝间隙平衡所需的胫骨内翻截骨越大(P < .0001)。
  • 轻度内翻膝81%和95%可在距机械轴3°和5°内平衡,中重度内翻膝仅37%和74%(P < .01)。
  • 总体95%模拟膝关节可在0° ± 5°内平衡,但50%屈膝内侧间隙较外侧更松。

核心结论

  • 应用cKATKA方法仅通过调整胫骨近端截骨而不松解韧带,可使全膝关节置换术达到0° ± 5°的机械轴对线。
  • 但预计近50%的全膝关节置换术会出现不理想的屈膝间隙平衡。

研究设计与样本

  • 利用607例连续机器人辅助全膝关节置换术(使用动态韧带张力计)中获得的对线数据和韧带张力,模拟cKATKA。
  • 股骨远端平行于原生关节线截骨并考虑软骨磨损,计算每膝实现伸膝间隙平衡所需的胫骨近端截骨。
  • 模拟对称后髁截骨并计算实现屈膝间隙平衡所需的胫骨截骨,最终确定并按照术前膝关节对线分类每膝的肢体对线和屈伸间隙平衡程度。

主要发现

  • 术前内翻畸形越重,实现伸膝间隙平衡所需的胫骨内翻截骨越大(P < .0001)。
  • 胫骨内翻角度与屈膝间隙平衡无相关性(P > .1)。
  • 轻度内翻畸形膝分别有81%和95%可实现平衡且整体肢体对线在距机械轴3°和5°以内。
  • 中重度内翻膝仅37%和74%可在上述对线边界内实现平衡(P < .01)。
  • 总体95%的模拟膝关节可实现平衡且整体对线在0° ± 5°以内。

局限性

  • 原文未报告局限性

以上解读依据论文摘要(全文未开放获取或许可不允许翻译转载)。

原文

METHODS: We simulated calipered kinematic alignment total knee arthroplasty (cKATKA) using alignment data and ligament tensions acquired during 607 consecutive robotic-assisted TKAs performed using a dynamic ligament tensor. The distal femur was resected parallel to the native joint line accounting for cartilage loss. The proximal tibial resection necessary to achieve extension gap balance was calculated for each knee. Similarly, symmetric posterior condylar resections prescribed by this method were simulated and the tibial resection needed to achieve a balanced flexion gap calculated. Finally, the resultant limb alignment and degree of joint balance in both flexion and extension of each knee were determined and categorized according to the preoperative knee alignment. RESULTS: Increasing preoperative varus deformity required a greater tibial varus cut to achieve a balanced extension gap (P < .0001). There was no correlation between tibial varus angle and flexion gap balance (P > .1). For mild varus deformities 81% and 95% of knees could be balanced and have an overall limb alignment within 3° and 5° from the mechanical axis respectively. For knees with moderate-severe varus, only 37% and 74% could be balanced within these alignment boundaries (P < .01). Overall, 95% of these simulated knees could be balanced with an overall alignment within 0° ± 5°. However, 50% of the simulated TKAs had looser medial gaps in flexion compared to the lateral gap. CONCLUSIONS: Application of the cKATKA method can yield TKAs within 0° ± 5° of mechanical axis alignment by simply adjusting the proximal tibial resection without ligament releases. However, an undesirable flexion gap balance was predicted in nearly 50% of the TKAs.

来源:J Arthroplasty,查看原文。版权归原作者所有。

引用

  1. Lee GC, Wakelin E, Plaskos C, et al. What Is the Alignment and Balance of a Total Knee Arthroplasty Performed Using a Calipered Kinematic Alignment Technique? J Arthroplasty. 2022. PMID: 35300880. doi:10.1016/j.arth.2022.01.065

供执业医师工作参考,不替代临床判断;数值与分级以指南原文为准。