Chitranjan S. Ranawat 奖:全膝关节骨水泥固定期间活动会显著降低胫骨假体固定强度
一项尸体研究利用32具躯干至足趾标本(64膝)评估四种全膝关节置换假体设计,每对标本一侧在骨水泥聚合期间保持不动、对侧在骨水泥混合后7分钟进行轻柔活动度与稳定性评估。不动组平均拔出力为5,462 N,高于活动组的4,473 N(P=0.001),且各假体设计间差异显著。作者推荐在胫骨假体骨水泥固定期间限制活动以提高固定强度。
要点
- 骨水泥聚合期间膝关节活动与胫骨假体固定强度显著下降相关(不动组5,462 N vs 活动组4,473 N,P=0.001)。
- 不动组各假体设计平均拔出力差异显著(假体A 7,230 N、B 5,806 N、C 5,325 N、D 3,486 N,P=0.007)。
- 作者推荐在所有测试设计中,胫骨假体骨水泥固定期间限制活动以提高固定强度。
核心结论
- 骨水泥聚合期间膝关节活动与胫骨假体固定强度显著下降相关。
- 活动状态下各假体设计均出现拔出力下降,且下降程度因设计而异。
- 作者推荐在所有测试设计中,胫骨假体骨水泥固定期间限制活动以提高固定强度。
研究设计与样本
- 尸体研究,利用32具躯干至足趾标本(64膝),评估四种当代全膝关节置换假体设计。
- 每种假体设计随机分配至一对尸体标本,并进行左右侧随机化,记录标本骨密度测定。
- 每侧胫骨假体均采用标准技术骨水泥固定:一侧在撞击后保持不动直至骨水泥完全聚合,对侧在骨水泥混合后7分钟进行轻柔活动度与稳定性评估。
- 对每具标本进行胫骨轴向拔出力测试和界面失败检查。
主要发现
- 不动组平均拔出力为5,462 N,高于活动组的4,473 N(P=0.001)。
- 不动组各假体设计平均拔出力差异显著:假体A 7,230 N、B 5,806 N、C 5,325 N、D 3,486 N(P=0.007)。
- 活动组各假体设计间方差亦显著(P≤0.001)。
- 假体A的拔出力显著高于假体D。
- 在假体-骨水泥界面失败 vs 骨失败标本中,平均拔出力显著较低(4,089±2,158 N vs 5,960±2,010 N,P<0.0025)。
关键数值与推荐
- 不动组平均拔出力5,462 N vs 活动组4,473 N(P=0.001)。
- 不动组假体A 7,230 N、B 5,806 N、C 5,325 N、D 3,486 N(P=0.007)。
- 假体-骨水泥界面失败标本平均拔出力4,089±2,158 N vs 骨失败标本5,960±2,010 N(P<0.0025)。
临床怎么用
- 作者推荐在所有测试的假体设计中,胫骨假体骨水泥固定期间限制活动以提高固定强度。
局限性
- 原文未报告局限性。
以上解读依据论文摘要(全文未开放获取或许可不允许翻译转载)。
原文
BACKGROUND: Aseptic tibial loosening following primary total knee arthroplasty persists despite technique and device-related advancements. The mechanisms for this mode of failure are not well understood. We hypothesized that knee movement while the cement was curing dispersed lipids at the implant-cement interface and would result in decreased tibial fixation strength. METHODS: A cadaveric study was performed utilizing 32 torso-to-toe specimens (64 knees). Four contemporary total knee arthroplasty designs were evaluated. Each implant design was randomly assigned to a cadaveric specimen pair with side-to-side randomization. Specimen densitometry was recorded. Each tibial implant was cemented using a standard technique. On one side, the tibial component was held without motion following impaction until complete cement polymerization. The contralateral knee tibial implant was taken through gentle range of motion and stability assessment 7 minutes after cement mixing. Axial tibial pull-out strength and interface failure examination was performed on each specimen. RESULTS: The average pull-out strength for the no motion cohort (5,462 N) exceeded the motion cohort (4,473 N) (P = .001). The mean pull-out strength between implant designs in the no motion cohort varied significantly (implant A: 7,230 N, B: 5,806 N, C: 5,325 N, D 3,486 N; P = .007). Similarly, the motion cohort inter-implant variance was significant (P ≤ .001). Intra-implant pull-out strength was significantly higher in implant A than D. The average pull-out strength was significantly lower in specimens that failed at the implant-cement interface vs bone failures (4,089 ± 2,158 N vs 5,960 ± 2,010 N, P < .0025). CONCLUSION: Knee motion during cement polymerization is associated with significant decreases in tibial implant fixational strength. Reduction in implant pull-out strength was identified with each implant design with motion and varied between designs. Across all tested designs, we recommend limiting motion while cementing the tibial implant to improve fixation strength.
引用
- Martin JR, Wronski PT, Schilkowsky RM, et al. Chitranjan S. Ranawat Award: Motion During Total Knee Cementing Significantly Decreases Tibial Implant Fixation Strength. J Arthroplasty. 2022. PMID: 35231563. doi:10.1016/j.arth.2022.02.091
供执业医师工作参考,不替代临床判断;数值与分级以指南原文为准。