文献速递关节外科

全髋关节置换术中独特设计的中度交联聚乙烯的意外磨损

Unexpected Wear of a Uniquely Designed Moderately Cross-Linked Polyethylene in Total Hip Arthroplasty.
PubMed 文献 · J Arthroplasty · 2022-02-05

研究比较了38例使用独特设计非热处理中度交联髋臼聚乙烯内衬的全髋关节置换术与21例使用另一种10年结果良好的中度交联聚乙烯的对照组的线性磨损率,发现研究组平均穿透率0.089 mm/y显著高于对照组0.047 mm/y(P=0.04),研究组45%磨损率超过骨溶解阈值(0.1 mm/y),对照组为24%,两例取回内衬宏观分析验证了影像学发现。

要点

  • 研究组平均穿透率0.089 mm/y显著高于对照组0.047 mm/y(P=0.04)。
  • 研究组45%磨损率超过骨溶解阈值0.1 mm/y,对照组为24%。
  • 两例取回内衬宏观分析验证了影像学磨损发现。

核心结论

  • 数据提示这种中度交联聚乙烯设计的磨损率意外偏高,研究组近一半处于骨溶解风险中。
  • 有必要对这种特定中度交联聚乙烯进行进一步的登记或数据库分析。

研究设计与样本

  • 所有全髋关节置换术均由资深作者完成。
  • 研究组包括38例使用所关注独特设计聚乙烯的全髋关节置换术,对照组为21例使用另一种10年结果良好的中度交联聚乙烯的全髋关节置换术。
  • 使用Martell髋关节分析套件进行二维线性股骨头穿透磨损测量,并对两例内衬进行取回分析。

主要发现

  • 研究组平均穿透率为0.089 mm/y,显著高于对照组平均穿透率0.047 mm/y(P=0.04)。
  • 研究组45%的磨损率高于骨溶解阈值(0.1 mm/y),对照组为24%。
  • 两例取回内衬的宏观分析验证了影像学发现。

关键数值与推荐

  • 骨溶解阈值为0.1 mm/y。
  • 研究组平均穿透率0.089 mm/y vs 对照组0.047 mm/y(P=0.04)。
  • 研究组45%磨损率高于0.1 mm/y vs 对照组24%。

临床怎么用

  • 原文未据此给出推荐。

局限性

  • 原文未报告局限性。

以上解读依据论文摘要(全文未开放获取或许可不允许翻译转载)。

原文

BACKGROUND: A uniquely designed, non-heat-treated moderately cross-linked acetabular polyethylene liner used in total hip arthroplasty (THA) demonstrated excessive wear during routine follow-up, prompting an evaluation of the linear wear rate. METHODS: All THAs were performed by the senior author. The study group included 38 THAs using the uniquely designed polyethylene in question, compared to a control group of 21 THAs using another moderately cross-linked polyethylene with good 10-year outcomes. Two-dimensional linear head penetration wear measurements were obtained using the Martell Hip Analysis Suite, and retrieval analysis was performed on two liners. RESULTS: The study group had a significantly higher average penetration rate of 0.089 mm/y than the control group average rate of 0.047 mm/y (P = .04). Forty-five percent of the study group had a wear rate above the osteolysis threshold (0.1 mm/y), compared to 24% in the control group. Macroscopic analysis of two retrieved liners validated the radiographic findings. CONCLUSION: The data suggest unexpectedly higher wear rates for a moderately cross-linked polyethylene design, with nearly half of the study group at risk for osteolysis. Further registry or database analyses of this particular moderately cross-linked polyethylene are warranted.

来源:J Arthroplasty,查看原文。版权归原作者所有。

引用

  1. Yakkanti RR, Ocksrider JL, Patel AA, et al. Unexpected Wear of a Uniquely Designed Moderately Cross-Linked Polyethylene in Total Hip Arthroplasty. J Arthroplasty. 2022. PMID: 35131388. doi:10.1016/j.arth.2022.01.093

供执业医师工作参考,不替代临床判断;数值与分级以指南原文为准。