SMILE术后110或160微米帽厚度的屈光矫正与生物力学强度:离体注压试验
研究将32枚人供体角膜按帽厚度(110或160微米)与球镜矫正(-4 D或-8 D)组合分为4组,在人工前房15或40 mm Hg压力下行SMILE前后测量。对于-8 D矫正,110微米帽较160微米帽产生更多前表面变平、更少后表面变陡及更多近视矫正;-4 D组无显著差异。注压试验显示SMILE后生物力学强度下降,两种帽厚度间相似。
要点
- 对于-8 D SMILE,110微米帽较160微米帽前表面变平更多、后表面变陡更少、近视矫正更多。
- -4 D SMILE中,110与160微米帽的屈光矫正变化无显著差异。
- SMILE后增加眼压导致前表面变陡,两种帽厚度间相似,提示生物力学强度下降程度相近。
核心结论
- 对于高度近视矫正,160微米帽较110微米帽导致更少前表面曲率变平、更多后表面变陡,因此近视矫正量更少。
- 注压试验显示SMILE后生物力学强度下降,使用110或160微米帽厚度时下降程度相似。
研究设计与样本
- 离体实验研究,将32枚人供体角膜分配至4组,组合两种帽厚度(110和160微米)与两种球镜矫正(-4 D和-8 D)。
- 每枚角膜安装于人工前房,通过连接的8%右旋糖酐介质柱调节腔压,在15或40 mm Hg压力下测量SMILE前后参数。
主要发现
- 对于-8 D SMILE,110微米帽较160微米帽前表面变平更多(Δr15,-8D,1.02±0.08 mm vs 0.60±0.17 mm),后表面变陡更少(Δr15,-8D,-0.19±0.11 mm vs -0.45±0.20 mm),近视矫正更多(ΔTCRP15,-8D,-6.30±0.96 D vs -4.55±1.66 D),P < 0.034。
- 对于-4 D SMILE,110与160微米帽的屈光矫正变化无显著差异(ΔTCRP15,-4D,110μm,-3.86±1.31 D vs ΔTCRP15,-4D,160μm,-3.57±1.27 D,P = 0.718)。
- SMILE后增加腔压至40 mm Hg导致前表面变陡(P < 0.014),110与160微米帽间相似(δr-4D,-0.13±0.14 mm vs -0.09±0.05 mm,P = 0.431)。
局限性
- 原文未报告局限性。
以上解读依据论文摘要(全文未开放获取或许可不允许翻译转载)。
原文
PURPOSE: To examine the refractive correction and corneal biomechanical strength after small incision lenticule extraction (SMILE) by using a 110- or 160-μm cap thickness. METHODS: Thirty-two human donor corneas were allocated into 4 groups, combining one of two cap thicknesses (110 and 160 μm) with one of two spherical corrections (-4 D and -8 D). Each cornea was mounted on an artificial anterior chamber. The chamber pressure was adjusted by an attached 8% dextran media column. The anterior and posterior sagittal 3-mm-diameter curvature (rsag3mm) and the total corneal refractive power (TCRP4mm,apex,zone) were obtained before and after SMILE at a chamber pressure of 15 or 40 mm Hg. The average changes after surgery (Δ = postoperative - preoperative) and at increased chamber pressure (δ = 40 mm Hg - 15 mm Hg) were compared. RESULTS: A 110-μm cap thickness caused more anterior flattening (Δr15,-8D, 1.02 ± 0.08 mm versus 0.60 ± 0.17 mm), less posterior steepening (Δr15,-8D, -0.19 ± 0.11 mm versus -0.45 ± 0.20 mm), and more myopic correction (ΔTCRP15,-8D, -6.30 ± 0.96 D versus -4.55 ± 1.66 D) than a 160-μm cap thickness for -8 D SMILE (P < 0.034), but not for -4 D SMILE (ΔTCRP15,-4D,110μm, -3.86 ± 1.31 D versus ΔTCRP15,-4D,160μm, -3.57 ± 1.27 D, P = 0.718). After SMILE, increased chamber pressure caused anterior steepening (P < 0.014), which was similar at cap thicknesses of 110 and 160 μm (δr-4D, -0.13 ± 0.14 mm versus -0.09 ± 0.05mm, P = 0.431). CONCLUSIONS: For high myopic corrections, a 160-μm cap caused less anterior curvature flattening and more posterior steepening than a 110-μm cap, and consequently less myopic correction. The inflation test revealed a reduction in the biomechanical strength after SMILE; this was similar when using a 110- or 160-μm cap thickness.
引用
- Damgaard IB, Ivarsen A, Hjortdal J, et al. Refractive Correction and Biomechanical Strength Following SMILE With a 110- or 160-μm Cap Thickness, Evaluated Ex Vivo by Inflation Test. Invest Ophthalmol Vis Sci. 2018. PMID: 29610851. doi:10.1167/iovs.17-23675
供执业医师工作参考,不替代临床判断;数值与分级以指南原文为准。