激光视力矫正中实现更平滑消融的最佳激光束特征
本研究建立逐点消融模拟模型,比较超高斯阶数、截断半径、光斑几何、重叠率和晶格几何对消融平滑度的影响。结果显示高斯轮廓理论上更平滑,圆形光斑优于方形,三角形晶格理论上优于网状晶格,截断光束增加粗糙度,PMMA上模拟粗糙度倾向于低于人角膜。
要点
- 高斯光束轮廓理论上产生更平滑消融,截断光束轮廓增加消融粗糙度。
- 圆形光斑几何比方形几何产生更低的消融粗糙度。
- 三角形晶格理论上比网状晶格产生更低的消融粗糙度。
核心结论
- 理论上,所提出的模型可用于以相对低成本在消融过程中使用的激光系统实现平滑度。
- 该模型可能改善结果质量,并可直接应用于改善术后表面质量。
研究设计与样本
- 研究建立逐点消融过程的严谨模拟模型,依据朗伯-比尔模型确定理论光束轮廓,并用光束轮廓相机测量准分子激光的强度光束轮廓。
- 对测量和理论光束轮廓均考虑圆形和方形两种光斑几何,模拟网状和三角形两种晶格,变化光斑重叠率和消融材料(角膜或聚甲基丙烯酸甲酯[PMMA])。
- 消融粗糙度以均方根除以层深度的平方根确定。
主要发现
- 截断光束轮廓增加消融粗糙度。
- 高斯轮廓理论上产生更平滑的消融。
- 圆形光斑几何相比方形几何产生更低的消融粗糙度。
- 三角形晶格理论上相比网状晶格产生更低的消融粗糙度。
- 理论建模光束轮廓相比测量光束轮廓显示更低的消融粗糙度,PMMA上模拟粗糙度倾向于低于人角膜。
关键数值与推荐
- 给定输入参数下,已找到最小化粗糙度的适当最优参数。
临床怎么用
- 作者认为该模型可用于以相对低成本在消融过程中使用的激光系统实现平滑度。
- 作者认为该模型可能改善结果质量,并可直接应用于改善术后表面质量。
局限性
- 原文未报告局限性。
以上解读依据论文摘要(全文未开放获取或许可不允许翻译转载)。
原文
PURPOSE: Controversial opinions exist regarding optimum laser beam characteristics for achieving smoother ablations in laser-based vision correction. The purpose of the study was to outline a rigorous simulation model for simulating shot-by-shot ablation process. The impact of laser beam characteristics like super Gaussian order, truncation radius, spot geometry, spot overlap, and lattice geometry were tested on ablation smoothness. METHODS: Given the super Gaussian order, the theoretical beam profile was determined following Lambert-Beer model. The intensity beam profile originating from an excimer laser was measured with a beam profiler camera. For both, the measured and theoretical beam profiles, two spot geometries (round and square spots) were considered, and two types of lattices (reticular and triangular) were simulated with varying spot overlaps and ablated material (cornea or polymethylmethacrylate [PMMA]). The roughness in ablation was determined by the root-mean-square per square root of layer depth. RESULTS: Truncating the beam profile increases the roughness in ablation, Gaussian profiles theoretically result in smoother ablations, round spot geometries produce lower roughness in ablation compared to square geometry, triangular lattices theoretically produce lower roughness in ablation compared to the reticular lattice, theoretically modeled beam profiles show lower roughness in ablation compared to the measured beam profile, and the simulated roughness in ablation on PMMA tends to be lower than on human cornea. For given input parameters, proper optimum parameters for minimizing the roughness have been found. CONCLUSIONS: Theoretically, the proposed model can be used for achieving smoothness with laser systems used for ablation processes at relatively low cost. This model may improve the quality of results and could be directly applied for improving postoperative surface quality.
引用
- Verma S, Hesser J, Arba-Mosquera S, et al. Optimum Laser Beam Characteristics for Achieving Smoother Ablations in Laser Vision Correction. Invest Ophthalmol Vis Sci. 2017. PMID: 28384723. doi:10.1167/iovs.16-21025
供执业医师工作参考,不替代临床判断;数值与分级以指南原文为准。