基于蒙特卡洛模型按ISO标准预测离散人工晶状体度数步长与制造公差对眼镜屈光不确定性的影响
该回顾性非随机横断面蒙特卡洛模拟研究基于16669例IOLMaster 700术前生物测量数据,评估Bausch and Lomb enVista与Alcon SA60AT两种人工晶状体的离散度数步长(PS)与ISO 11979度数标签公差(LT)对屈光结果不确定性(REFU)的影响。结果显示两种晶状体由PS导致的REFU为0.11至0.12 dpt,由LT导致的REFU为0.18至0.19 dpt。作者认为PS导致的REFU可能被容忍,而LT导致的REFU不可避免。
要点
- 两种晶状体由离散度数步长导致的屈光结果不确定性为0.11至0.12 dpt。
- 两种晶状体由制造公差导致的屈光结果不确定性为0.18至0.19 dpt。
- 制造公差导致的屈光结果不确定性在白内障术后无法避免。
核心结论
- 外科医生和患者通常了解离散度数步长对屈光结果不确定性的影响,因此这些不确定性可能被容忍。
- 由制造公差导致的屈光结果不确定性不可避免,因为包装上未报告真实测量的晶状体度数,从而在术后实际屈光中产生背景噪声。
研究设计与样本
- 回顾性非随机横断面蒙特卡洛模拟研究。
- 评估包含16669例IOLMaster 700术前生物测量数据的数据集。
- 考虑Bausch and Lomb enVista和Alcon SA60AT两种现代人工晶状体的度数步长和交付范围进行模拟。
- 假设度数步长或制造公差导致的不确定性分别按±½人工晶状体度数步长或ISO 11979制造公差呈正态分布。
主要发现
- 两种晶状体由离散度数步长导致的屈光结果不确定性范围为0.11至0.12 dpt。
- 由于enVista和SA60AT低/高屈光度晶状体的度数步长较大,屈光结果不确定性在初始近视/远视眼中更为突出。
- 两种晶状体由制造公差导致的屈光结果不确定性范围为0.18至0.19 dpt。
- 由于制造公差随人工晶状体屈光度呈阶梯式增加,屈光结果不确定性在需要高屈光度人工晶状体的初始远视眼中以及交付范围较宽的高屈光度晶状体中更为普遍。
临床怎么用
- 原文未据此给出推荐。
局限性
- 原文未报告局限性。
以上解读依据论文摘要(全文未开放获取或许可不允许翻译转载)。
原文
PURPOSE: The purpose of this study was to develop a concept for predicting the effects of both discrete intraocular lens (IOL) power steps (PS) and power labelling tolerances (LT) on the uncertainty of the refractive outcome (REFU). DESIGN: Retrospective non-randomised cross-sectional Monte Carlo simulation study. METHODS: We evaluated a dataset containing 16 669 IOLMaster 700 preoperative biometric measurements. The PS and the delivery range of two modern IOLs (Bausch and Lomb enVista and Alcon SA60AT) were considered for this Monte Carlo simulation. The uncertainties from PS or LT were assumed to be normally distributed according to ±½ the IOL PS or the ISO 11979 LT. REFU was recorded and analysed for all simulations. RESULTS: With both lenses the REFU from discrete PS ranged from 0.11 to 0.12 dpt. Due to the larger PS for low/high power lenses with the enVista/SA60AT, REFU is more dominant in initially myopic/hyperopic eyes. REFU from LT ranged from 0.18 to 0.19 dpt for both lenses. Since LT increases stepwise with IOL power, REFU is more prevalent in initially hyperopic eyes requiring high IOL power values, and for lenses with a wide delivery range towards higher powers. CONCLUSIONS: Since surgeons and patients are typically aware of the effect of discrete PS on REFU, these might be tolerated in cataract surgery. However, REFU resulting from LT is inevitable while the true measured IOL power is not reported on the package, leading to background noise in postoperative achieved refraction.
引用
- Langenbucher A, Szentmáry N, Cayless A, et al. Prediction of spectacle refraction uncertainties with discrete IOL power steps and manufacturing tolerances according to ISO using a Monte Carlo model. Br J Ophthalmol. 2024. PMID: 37495264. doi:10.1136/bjo-2023-323921
供执业医师工作参考,不替代临床判断;数值与分级以指南原文为准。