使用智能手机三维表面成像技术制造定制三维打印眼镜
本质量改进研究分析病例系列数据,评估智能手机三维表面成像(3DSI)捕捉面部解剖用于定制眼镜设计的可行性。关键配镜参数在MRI与3DSI扫描间的平均差为1.47 mm(SD 0.79),20例1至17岁颅面异常患者均获得成功配戴,从初始原型到最终镜架平均修改1.7次。
要点
- 智能手机3DSI与MRI测量的配镜关键参数平均差1.47 mm(SD 0.79,范围0.3-4.60 mm)。
- 20例1至17岁颅面异常患者经患者、家长或监护人判断均实现成功配戴(每日戴镜无刺激)。
- 从初始原型到最终镜架生产平均修改1.7次。
核心结论
- 智能手机3DSI结合广泛可用的3D打印技术可为颅面异常患者制作成功配戴的定制镜架。
- 这一可及且耐受良好的成像过程可能对存在弱视所致视力丧失风险患者的戴镜依从性有影响。
研究设计与样本
- 质量改进研究,分析来自一家初级学术中心及美国多地转诊中心的病例系列数据。
- 评估对象为因颅面异常导致戴镜依从性差的患者,纳入其报告的配戴描述。
- 3DSI扫描成功的定义为关键配镜参数可确定且MRI与3DSI测量差异小于5%。
主要发现
- 配镜关键参数(面宽、耳桥至鼻桥距离、瞳孔中心至鼻桥中心距离、外眦至内眦距离、耳垂直偏移、鼻桥宽度)在MRI与3DSI扫描间相似,平均差1.47 mm(SD 0.79,范围0.3-4.60 mm)。
- 20例1至17岁颅面异常患者经患者、家长或监护人判断均实现成功配戴(报告每日戴镜无刺激)。
- 使用3DSI技术从初始原型到最终镜架生产平均修改1.7次。
关键数值与推荐
- 3DSI扫描成功标准:关键配镜参数可确定且MRI与3DSI测量差异小于5%。
- 配镜成功标准:患者、家长或监护人报告每日戴镜依从且无刺激。
临床怎么用
- 原文未据此给出推荐。
局限性
- 原文未报告局限性。
以上解读依据论文摘要(全文未开放获取或许可不允许翻译转载)。
原文
IMPORTANCE: Finding a suitable fit in glasses for pediatric patients with congenital and acquired craniofacial abnormalities is difficult; consequently, these children are at high risk of vision loss secondary to refractive amblyopia as they often have poor adherence to daily glasses wearing. Custom 3-dimensional (3D)-printed glasses may have an improved design and fit, but access is limited by the availability of computed tomography and magnetic resonance imaging (MRI). OBJECTIVE: To describe a method for using a commercially available smartphone 3D surface imaging (3DSI) technique to capture facial anatomy as a basis for custom glasses design. DESIGN, SETTING, AND PARTICIPANTS: This quality improvement study analyzes data from a case series in a primary academic center with multiple referral centers throughout the United States. The evaluation included reported fit descriptions from patients with poor glasses adherence due to craniofacial abnormalities. MAIN OUTCOMES AND MEASURES: Key anatomic parameters for glasses fit (face width, distance from ear bridge to nasal bridge, distance from center of pupil to center of nasal bridge, distance from lateral to medial canthus, ear vertical offset, and nasal bridge width) were compared between scans. A 3DSI scan was considered successful if these key parameters could be determined and the difference in measurements was less than 5% between MRI and 3DSI. A second outcome measure included the fit of glasses designed by the 3DSI method as reported by the patient, parent, or guardian. RESULTS: Measurements of key parameters for glasses fit were similar across MRI and 3DSI scans with a mean (SD) difference of 1.47 (0.79) mm between parameters (range, 0.3-4.60 mm). Among 20 patients aged 1 to 17 years with craniofacial abnormalities, all achieved a successful fit (reporting daily glasses adherence without irritation) as judged by the patient, parent, or guardian. A mean of 1.7 revisions were made from initial prototype to final frame production using 3DSI technology. CONCLUSIONS AND RELEVANCE: This study demonstrated that smartphone-enabled 3DSI coupled with widely available 3D printing technology can produce custom frames with a successful fit for patients with craniofacial anomalies. This accessible and well-tolerated imaging process may have implications for adherence with glasses wearing among patients at risk of vision loss due to amblyopia.
引用
- de Alba Campomanes AG, Meer E, Clarke M, et al. Using a Smartphone 3-Dimensional Surface Imaging Technique to Manufacture Custom 3-Dimensional-Printed Eyeglasses. JAMA Ophthalmol. 2022. PMID: 36048438. doi:10.1001/jamaophthalmol.2022.3312
供执业医师工作参考,不替代临床判断;数值与分级以指南原文为准。