预测筛查检出肺结节的恶性风险:平均直径还是体积
该研究基于两个多中心肺癌筛查试验数据,比较了使用平均直径或体积的结节恶性风险预测工具,以及计算机辅助检测与放射科医生测量的性能。结果显示,基于CAD的平均直径和体积模型均具有优秀的区分度和校准度,在NLST验证数据中AUC分别为0.810和0.821,与放射科医生测量模型相似。结论是CAD-based结节直径或体积均可用于辅助预测结节恶性风险。
要点
- CAD基于平均直径或体积的模型均能优秀预测肺结节恶性风险。
- CAD模型性能与放射科医生测量模型相似。
- 临床可选用CAD测量的直径或体积辅助风险预测。
核心结论
- 基于CAD的结节平均直径或体积均可用于辅助预测筛查检出肺结节的恶性风险。
研究设计与样本
- 研究使用两个多中心肺癌筛查试验数据,开发并验证多变量逻辑回归模型。
- 开发数据来自Pan-Canadian Early Detection of Lung Cancer Study的基线低剂量CT扫描。
- 验证数据来自NLST中平均直径≥3 mm肺结节子集,癌症结节按大小匹配无癌症结节。
- 测量使用CIRRUS Lung Screening Workstation。
主要发现
- 基于CAD的平均直径和体积模型均显示优秀的区分度和校准度,AUC均为0.947。
- 两个CAD模型预测性能与基于放射科医生的模型相似。
- 在NLST验证数据中,CAD平均直径和体积模型的AUC分别为0.810和0.821。
- 这些性能统计与使用放射科医生测量最大直径的Pan-Canadian模型相似。
临床怎么用
- 在肺癌筛查中,可使用CAD测量的结节平均直径或体积辅助预测恶性风险。
以上解读依据论文摘要(全文未开放获取或许可不允许翻译转载)。
原文
OBJECTIVE: In lung cancer screening practice low-dose computed tomography, diameter, and volumetric measurement have been used in the management of screen-detected lung nodules. The aim of this study was to compare the performance of nodule malignancy risk prediction tools using diameter or volume and between computer-aided detection (CAD) and radiologist measurements. METHODS: Multivariable logistic regression models were prepared by using data from two multicenter lung cancer screening trials. For model development and validation, baseline low-dose computed tomography scans from the Pan-Canadian Early Detection of Lung Cancer Study and a subset of National Lung Screening Trial (NLST) scans with lung nodules 3 mm or more in mean diameter were analyzed by using the CIRRUS Lung Screening Workstation (Radboud University Medical Center, Nijmegen, the Netherlands). In the NLST sample, nodules with cancer had been matched on the basis of size to nodules without cancer. RESULTS: Both CAD-based mean diameter and volume models showed excellent discrimination and calibration, with similar areas under the receiver operating characteristic curves of 0.947. The two CAD models had predictive performance similar to that of the radiologist-based model. In the NLST validation data, the CAD mean diameter and volume models also demonstrated excellent discrimination: areas under the curve of 0.810 and 0.821, respectively. These performance statistics are similar to those of the Pan-Canadian Early Detection of Lung Cancer Study malignancy probability model with use of these data and radiologist-measured maximum diameter. CONCLUSION: Either CAD-based nodule diameter or volume can be used to assist in predicting a nodule's malignancy risk.
引用
- Tammemagi M, Ritchie AJ, Atkar-Khattra S, et al. Predicting Malignancy Risk of Screen-Detected Lung Nodules-Mean Diameter or Volume. J Thorac Oncol. 2018. PMID: 30368011. doi:10.1016/j.jtho.2018.10.006
供执业医师工作参考,不替代临床判断;数值与分级以指南原文为准。