3D打印辅助患者特异性聚甲基丙烯酸甲酯颅骨修补术:16例连续病例系列
本研究开发了一种3D打印辅助制作患者特异性颅骨修补植入物的新方法,并报告了16例因去骨瓣减压术后大面积颅骨缺损且骨瓣不可用的连续病例。中位手术时间121分钟,中位术中失血量300 mL,平均随访6个月。并发症发生率为43.8%(7/16),其中37.5%(6/16)需再次手术。结论认为该工作流程可行,植入物贴合良好且美观。
要点
- 3D打印辅助制作患者特异性PMMA植入物用于颅骨修补可行。
- 16例中7例(43.8%)出现并发症,6例(37.5%)需再次手术。
- 术后CT显示植入物贴合良好,美容效果满意。
核心结论
- 3D打印辅助术中及时制作患者特异性植入物覆盖颅骨缺损的工作流程可行。
- 结果美容效果好,术后CT显示植入物贴合良好。
研究设计与样本
- 病例系列,纳入16例去骨瓣减压术后大面积颅骨缺损且骨瓣不可用的连续患者。
- 采用3D打印辅助 molding 技术制作患者特异性植入物,分析术前、术中及术后数据。
主要发现
- 初次开颅指征:创伤性脑损伤4例(25%)、急性硬膜下血肿4例(25%)、缺血性卒中3例(18.8%)、肿瘤3例(18.8%)、动脉瘤破裂2例(12.5%)。
- 中位手术时间121分钟(范围89-206分钟),中位术中失血量300 mL(范围100-3300 mL)。
- 平均随访6个月(范围0-21个月)。
- 并发症7例(43.8%),其中6例(37.5%)需再次手术:硬膜外血肿清除3例(50%)、硬膜外积液分流1例(16.7%)、皮瓣坏死1例(16.7%);1例(16.7%)出现慢性无症状硬膜下积液,随访稳定。
临床怎么用
- 对于去骨瓣减压术后大面积颅骨缺损且自体骨瓣不可用的患者,可考虑采用3D打印辅助制作患者特异性PMMA植入物进行颅骨修补。
- 术后需关注硬膜外血肿、硬膜外积液、皮瓣坏死及硬膜下积液等并发症。
局限性
- 样本量小(16例),随访时间短(平均6个月,范围0-21个月)。
- 为单中心病例系列,缺乏对照组。
以上解读依据论文摘要(全文未开放获取或许可不允许翻译转载)。
原文
BACKGROUND: To develop a novel 3D-printer-assisted method to fabricate patient-specific implants for cranioplasty and to demonstrate its feasibility and its use in 16 consecutive cases. METHODS: We report on 16 consecutive patients who have undergone cranioplasty surgery for an extensive skull defect after decompressive surgery and in which the bone flap was not available. We present the workflow for the implant production using a 3D-printer-assisted molding technique. Preoperative, intraoperative, and postoperative data were analyzed/evaluated. RESULTS: Eleven out of our 16 patients (68.7%) presented with extensive hemispheric bone defects. Indication for initial craniotomy were traumatic brain injury (4; 25%), acute subdural hematoma (4; 25%), ischemic stroke (3; 18.8%), tumor (3; 18.8%), and ruptured aneurysm (2; 12.5%). Median (range) operation time was 121 (89-206) minutes. Median (range) intraoperative blood loss was 300 (100-3300) mL. The mean (range) follow-up period is 6 (0-21) months. Complications occurred in 7 out of our 16 patients (43.8%), in 6 (37.5%) of which a reoperation was required to evacuate an extra-axial hematoma (3; 50%), for shunting of an epidural fluid collection (1; 16.7%), or for skin flap necrosis (1; 16.7%). One patient (16.7%) developed a chronic asymptomatic subdural fluid collection that was stable over the follow-up period. CONCLUSIONS: Our workflow to intraoperatively produce patient-specific implants in a timely manner to cover cranial defects proved to be feasible. The results are cosmetically appealing, and postoperative CT scans show well-fitting implants. As implantable printable substrates are already available, we aim to advance and certify 3D-printed patient-specific implants in the near future.
引用
- Schön SN, Skalicky N, Sharma N, et al. 3D-Printer-Assisted Patient-Specific Polymethyl Methacrylate Cranioplasty: A Case Series of 16 Consecutive Patients. World Neurosurg. 2021. PMID: 33418118. doi:10.1016/j.wneu.2020.12.138
供执业医师工作参考,不替代临床判断;数值与分级以指南原文为准。