文献速递脑血管病外科神经重症

三维打印神经介入模型的设计与物理特性:系统综述

Design and Physical Properties of 3-Dimensional Printed Models Used for Neurointervention: A Systematic Review of the Literature.
PubMed 文献 · Neurosurgery · 2020-01-01

该系统综述检索2000年1月1日至2018年9月30日多个数据库,纳入23篇关于神经介入三维打印血管模型的研究,总结其设计、物理特性、准确性与实验结局。结果显示模型在材料、设计和血管重建范围上存在差异,仅一项原型研究报告顺应性与润滑性,作者呼吁对模型进行客观表征并开发人群代表性模型。

要点

  • 神经介入三维打印模型在材料与血管重建范围上差异显著。
  • 仅一项原型研究报告了顺应性与润滑性,客观表征不足。
  • 作者建议开发人群代表性模型用于技能提升或器械测试。

核心结论

  • 三维打印模型在材料、设计和血管重建范围上存在差异,需要客观表征并开发人群代表性模型。

研究设计与样本

  • 系统综述检索PubMed、Web of Science、Compendex、Cochrane和Inspec数据库2000年1月1日至2018年9月30日文献,共纳入23篇。

主要发现

  • 9项研究描述用于卒中介入的三维打印模型,Tango Plus(Stratasys)是最常用材料。
  • 4项研究描述人群代表性几何模型,其余研究报道患者特异性血管几何。
  • 8项研究报告完整重建Willis环、前循环和后循环,4项研究报告包含颅外血管的模型。
  • 仅一项原型研究报告顺应性和润滑性;循环系统包括手动冲洗、可编程活塞、蠕动泵和搏动泵。
  • 结局包括脑梗死溶栓分级、取栓后血流恢复、手术表现和定性反馈。

临床怎么用

  • 选择三维打印神经介入模型时需注意材料、血管重建范围和循环系统的差异。
  • 现有模型可用于培训、教育和器械测试,但物理特性表征不足。

局限性

  • 纳入研究数量有限(23篇),且仅一项原型研究报告顺应性与润滑性。
  • 模型设计和物理特性缺乏统一标准,结局评价多为定性反馈。

以上解读依据论文摘要(全文未开放获取或许可不允许翻译转载)。

原文

BACKGROUND: Three-dimensional (3D) printing has revolutionized training, education, and device testing. Understanding the design and physical properties of 3D-printed models is important. OBJECTIVE: To systematically review the design, physical properties, accuracy, and experimental outcomes of 3D-printed vascular models used in neurointervention. METHODS: We conducted a systematic review of the literature between January 1, 2000 and September 30, 2018. Public/Publisher MEDLINE (PubMed), Web of Science, Compendex, Cochrane, and Inspec databases were searched using Medical Subject Heading terms for design and physical attributes of 3D-printed models for neurointervention. Information on design and physical properties like compliance, lubricity, flow system, accuracy, and outcome measures were collected. RESULTS: A total of 23 articles were included. Nine studies described 3D-printed models for stroke intervention. Tango Plus (Stratasys) was the most common material used to develop these models. Four studies described a population-representative geometry model. All other studies reported patient-specific vascular geometry. Eight studies reported complete reconstruction of the circle of Willis, anterior, and posterior circulation. Four studies reported a model with extracranial vasculature. One prototype study reported compliance and lubricity. Reported circulation systems included manual flushing, programmable pistons, peristaltic, and pulsatile pumps. Outcomes included thrombolysis in cerebral infarction, post-thrombectomy flow restoration, surgical performance, and qualitative feedback. CONCLUSION: Variations exist in the material, design, and extent of reconstruction of vasculature of 3D-printed models. There is a need for objective characterization of 3D-printed vascular models. We propose the development of population representative 3D-printed models for skill improvement or device testing.

来源:Neurosurgery,查看原文。版权归原作者所有。

引用

  1. Waqas M, Mokin M, Lim J, et al. Design and Physical Properties of 3-Dimensional Printed Models Used for Neurointervention: A Systematic Review of the Literature. Neurosurgery. 2020. PMID: 32392300. doi:10.1093/neuros/nyaa134

供执业医师工作参考,不替代临床判断;数值与分级以指南原文为准。