文献速递疝与腹壁外科围术期管理与 ERAS

两种轻量聚丙烯补片在微创腹股沟疝手术中的初步评价

A preliminary evaluation of two different meshes in minimally invasive inguinal hernia surgery.
PubMed 文献 · Surg Endosc · 2020-03-30

本研究将48例受试者随机分配至3DMax™补片或Ultrapro®补片组,比较腹腔镜与机器人腹股沟疝修补术中补片置入时间。结果显示两种补片置入时间无显著差异(p=0.523),机器人置入时间显著增加(p<.0001),补片难度自我评估无显著差异。

要点

  • 两种轻量聚丙烯补片置入时间无显著差异,可依据外科医生偏好互换使用。
  • 机器人补片置入时间较腹腔镜显著延长,可能与机器人缝合力学及学习曲线有关。
  • 补片置入难度NASA-TLX自我评估在两种补片间无显著差异。

核心结论

  • 两种轻量聚丙烯补片在微创腹股沟疝修补术中的置入时间无显著差异,可依据外科医生偏好互换使用。

研究设计与样本

  • 随机对照初步评价,2015年1月至2016年6月纳入50例受试者,排除2例,最终分析48例。
  • 受试者在手术前立即随机分配至3DMax™补片或Ultrapro®补片组。

主要发现

  • 48例合格受试者中多数为白人(N=42,88%)、男性(N=37,77%),中位年龄63岁。
  • 机器人补片置入时间显著增加,与补片类型无关(p<.0001)。
  • 两种补片置入难度NASA-TLX自我评估无显著差异。
  • 补片类型对置入时间无显著影响,与是否使用机器人无关(p=0.523)。

临床怎么用

  • 两种轻量聚丙烯补片可依据外科医生偏好互换使用。
  • 机器人腹股沟疝修补术中补片置入时间延长,需考虑机器人缝合力学及学习曲线的影响。

以上解读依据论文摘要(全文未开放获取或许可不允许翻译转载)。

原文

BACKGROUND: Many meshes are available for use in laparoscopic inguinal hernia repair. The surgeon must consider several factors when choosing a mesh for hernia repair including clinical outcomes, cost, and ease of use. The purpose of this study was to compare two different lightweight polypropylene meshes for laparoscopic and robotic inguinal hernia repairs. METHODS: Subjects were randomized immediately before surgery. Data were reported in N (%) and median [Q1-Q3], comparisons of mesh insertion time were tested using a 2 × 2 ANOVA on the ranked times, comparisons between categorical variables were tested with Fisher's Exact, and all data were analyzed using SAS® 9.4 (SAS Institute, Inc.). RESULTS: Between January 2015 and June 2016, 50 subjects were enrolled; two were excluded. Of 48 eligible subjects, most were Caucasian (N = 42, 88%), male (N = 37, 77%), with a median age of 63, and were randomized evenly between 3DMax™ mesh and Ultrapro® mesh. Robotic mesh placement significantly increased insertion time regardless of mesh type (p < .0001). When comparing NASA-TLX self-assessment surveys, there was no significant difference between the meshes in difficulty of placement. The type of mesh did not significantly impact the insertion time regardless of robot use (p = 0.523). CONCLUSION: Our data demonstrate that mesh insertion times comparing two different lightweight polypropylene meshes were not significantly different. Increased insertion times associated with robotic repair are likely due to the mechanics of robotic suturing and associated learning curve. Our data suggest that these meshes can be used interchangeably based on the surgeon's preference. CLINICAL TRIAL REGISTRATION NUMBER: NCT01825187.

来源:Surg Endosc,查看原文。版权归原作者所有。

引用

  1. Bilezikian JA, Tenzel PL, Johnson RG, et al. A preliminary evaluation of two different meshes in minimally invasive inguinal hernia surgery. Surg Endosc. 2020. PMID: 32232645. doi:10.1007/s00464-020-07512-9

供执业医师工作参考,不替代临床判断;数值与分级以指南原文为准。