文献速递胃肠外科疝与腹壁外科围术期管理与 ERAS

深度不足:建模达芬奇Xi「减重」长套管浅置对腹壁肌肉的影响

Not deep enough: Modeling the effect of shallow placement of the DaVinci Xi "bariatric" long trocar on the muscular abdominal wall.
PubMed 文献 · Surg Endosc · 2023-07-06

本研究基于达芬奇Xi机械臂专利图,用三角法建模长套管浅置时套管处腹壁的侧向位移。模型参数取套管浅置深度1-7 cm、器械尖端深度0-20 cm、尖端侧向移动0-14.1 cm(假定最大偏离中线角度45°);腹壁位移随各参数偏离正交中线而成比例增大,最大浅置时最大腹壁位移约7.0 cm。作者结论认为当前Xi臂设计使长套管无法在不破坏旋转中心的前提下安全使用,从而增加疝发生风险。

要点

  • Xi长套管比标准套管多5 cm远端长度,可穿越过厚的腹壁组织。
  • Xi刚性平行四边形结构将旋转中心保留在套管上的黑色标记处,长套管与标准套管的该标记距近端距离相同。
  • 浅置长套管会破坏旋转中心,导致机械臂对穿刺孔产生未被察觉的钝性扩大,增加疝风险。

核心结论

  • 作者结论认为,当前Xi臂设计使真正的长套管无法在不破坏旋转中心的情况下安全使用,从而带来疝发生风险。

研究设计与样本

  • 本研究为基于达芬奇Xi机械臂专利(美国专利#5931832)示意图的三角法建模研究,未涉及患者样本。

主要发现

  • 模型参数范围为套管浅置深度1 cm至7 cm、器械尖端深度0 cm至20 cm、器械尖端侧向移动0.0 cm至14.1 cm(假定最大偏离中线角度45°)。
  • 腹壁位移随各器械尖端参数达到偏离正交中线的最大偏差而成比例增大。
  • 最大浅置时的最大腹壁位移约为7.0 cm。

局限性

  • 原文未报告局限性。

以上解读依据论文摘要(全文未开放获取或许可不允许翻译转载)。

原文

INTRODUCTION: The DaVinci Xi Robotic Surgical System (Xi) long cannula (Intuitive Surgical Company, Sunnyvale, CA) provides five additional centimeters of distal length compared to the standard Xi trocar. The extra length allows the cannula to traverse prohibitively thick body wall tissue. Our aims are to quantitatively model the consequences of not preserving the rotational centerpoint of motion (RCM) at the muscular abdominal wall. This is an essential tenet in robotic surgery; it is violated with shallow placement of the long trocar. This leads to unchecked, unnoticed blunt widening of port sites by the robotic arm, increasing hernia risk. METHODS: We begin with an exploration of the schematic of the Xi robotic arm as patented by Intuitive (U.S. Patent #5931832). We trigonometrically model the lateral displacement of the abdominal wall at the trocar site with respect to vertical trocar shallowness, instrument tip depth, and instrument tip lateral motion from neutral midline. RESULTS: The rigid parallelogram movement structure of the Xi preserves the RCM at the thick black marker printed on every Xi cannula. By limitation of design, both long and standard trocars must have this marker at the exact same distance from their proximal end. The value ranges of our model parameters (presuming a reasonable maximum orientation angle of 45° from midline) are: trocar shallowness [1 cm, 7 cm]; instrument tip depth [0 cm, 20 cm]; instrument tip lateral movement [0.0 cm, 14.1 cm]. Abdominal wall displacement increased proportionally as each instrument tip parameter reached its maximum deviation from the orthogonal midline as described in the plot figure. Maximal wall displacement at maximal shallowness was approximately 7.0 cm. CONCLUSION: Robotic surgery revolutionizes modern operation, particularly within bariatrics. However, the current Xi arm design disallows a true long trocar to be used safely without compromising the RCM, thereby risking hernia development.

来源:Surg Endosc,查看原文。版权归原作者所有。

引用

  1. Qafiti FN, Buicko JL. Not deep enough: Modeling the effect of shallow placement of the DaVinci Xi "bariatric" long trocar on the muscular abdominal wall. Surg Endosc. 2023. PMID: 37415018. doi:10.1007/s00464-023-10207-6

供执业医师工作参考,不替代临床判断;数值与分级以指南原文为准。