用于基础鼻内镜训练的三维打印模型的创建与验证
研究制作了儿童与成人鼻腔及鼻窦术后三维打印模型,由5名鼻科医生用5点Likert量表评价保真度与实用性,并比较5名住院医师完成预定任务的时间。模型24小时内成型且单个成本低于100元人民币(15美元),保真度与实用性总分均高于4.0,专家完成任务时间显著短于住院医师(均p<0.05)。
要点
- 三维打印儿童与成人鼻腔及鼻窦术后模型24小时内成型,单个成本低于100元人民币(15美元)。
- 5名鼻科医生对模型保真度与内镜训练实用性的总体评分均高于4.0分(5点Likert量表)。
- 5名专家完成全部预定任务的时间显著短于5名住院医师(均p<0.05)。
核心结论
- 用本研究的桌面级三维打印机制作的鼻腔与鼻窦模型保真度高、成本低,对训练基础内镜技能有用。
研究设计与样本
- 选取无鼻部疾病儿童和鼻中隔偏曲成人的CT数据制作儿童与成人鼻腔模型,选取4个月前接受内镜鼻窦手术成人的CT数据制作鼻窦术后模型。
- 模型由本研究的桌面级三维打印机打印后,5名鼻科医生用5点Likert量表评价保真度与实用性。
- 5名鼻科医生与5名住院医师分别完成一组预先设定的任务以补充内容验证,各任务完成时间差异用Mann-Whitney U检验分析。
主要发现
- 所有模型均在24小时内成型,每个模型总成本低于100元人民币(15美元)。
- 内镜训练中保真度与实用性的总体评分均高于4.0分。
- 专家完成全部任务所用时间显著少于住院医师(均p<0.05)。
关键数值与推荐
- 保真度与实用性采用5点Likert量表评价,总体评分均高于4.0分。
- 各任务完成时间的组间比较均p<0.05。
临床怎么用
- 作者认为该桌面级三维打印机制作的鼻腔与鼻窦模型保真度高、成本低,可用于训练基础内镜技能。
局限性
- 原文未报告局限性。
以上解读依据论文摘要(全文未开放获取或许可不允许翻译转载)。
原文
BACKGROUND: Three-dimensional (3D) printed models have been shown to be promising in surgical training in rhinology. The objectives of this study were to develop a set of 3D-printed models including the pediatric and adult nasal cavity, and the postsurgical paranasal sinuses, and to assess the face and content validity in endoscopic training. METHODS: The computed tomography (CT) data of a pediatric patient without nasal disorders and an adult patient with nasal septal deviation were selected to produce the models of the pediatric and adult nasal cavity, and the CT data of an adult patient who underwent endoscopic sinus surgery 4 months ago was chosen to create the paranasal sinus model. After the models were printed by our desktop-level 3D printer, 5 rhinologists used the 5-point Likert scales to evaluate the fidelity and utility. Additionally, a group of prespecified tasks were completed by the rhinologists and 5 residents respectively for supplementary content validation. The difference of time used in completing each task was analyzed by Mann-Whitney U test. RESULTS: All the models were prototyped in 24 hours, and the total cost for each model was less than 100 CNY (15 USD). The overall scores for fidelity and usefulness in endoscopic training were above 4.0. The experts accomplished all tasks using significantly less time than the residents (all p < 0.05). CONCLUSION: The models of nasal cavities and paranasal sinuses made by our desktop-level 3D printer are high-fidelity, low-cost, and useful in training basic endoscopic skills.
引用
- Zhuo C, Lei L, Yulin Z, et al. Creation and validation of three-dimensional printed models for basic nasal endoscopic training. Int Forum Allergy Rhinol. 2019. PMID: 30748103. doi:10.1002/alr.22306
供执业医师工作参考,不替代临床判断;数值与分级以指南原文为准。