患者特异性三维打印鼻窦与颅底内镜手术模型评估
本研究于2017年4月至6月在单中心开展,招募7名耳鼻咽喉科住院医师和2名主治医师,评估高分辨率三维打印鼻窦颅底模型的解剖准确性与触觉反馈。CT比较显示患者与模型测量差异小于5%,导航确认13个标志点准确至1毫米内,Likert量表总体解剖准确性均分4.00(SD 0.71),触觉反馈均分4.67(SD 0.5)。结论认为该模型具有解剖和触觉准确性,有望用于手术培训和术前规划。
要点
- 三维打印模型与患者CT测量差异小于5%,13个手术标志点导航准确至1毫米内。
- 参与者对总体解剖准确性评分均分4.00(SD 0.71),触觉反馈评分均分4.67(SD 0.5)。
- 该技术有望作为尸体解剖的补充或替代模拟培训平台。
核心结论
- 高分辨率三维打印鼻窦和颅底模型可达到解剖和触觉准确性,有望用于手术培训、术前规划及模拟训练。
研究设计与样本
- 单中心研究,2017年4月1日至6月1日招募7名耳鼻咽喉科住院医师和2名主治医师,评估三维打印模型的解剖准确性和触觉反馈。
主要发现
- CT比较显示患者与三维模型测量差异小于5%。
- 图像导航确认13个手术标志点准确至1毫米内。
- Likert量表总体解剖准确性均分4.00(SD 0.71),触觉反馈均分4.67(SD 0.5)。
关键数值与推荐
- 解剖准确性通过CT比较设定解剖标志点(如筛板深度)评估,差异小于5%。
- 图像导航评估13个手术标志点,准确至1毫米内。
- Likert量表1至5分,1表示强烈不同意,5表示强烈同意。
临床怎么用
- 该模型可用于耳鼻咽喉科住院医师和主治医师的鼻窦颅底手术模拟培训。
- 可作为术前规划工具,帮助理解患者特异性解剖。
- 可作为尸体解剖的补充或替代模拟训练平台。
以上解读依据论文摘要(全文未开放获取或许可不允许翻译转载)。
原文
IMPORTANCE: Three-dimensional (3D) printing is an emerging tool in the creation of anatomical models for simulation and preoperative planning. Its use in sinus and skull base surgery has been limited because of difficulty in replicating the details of sinus anatomy. OBJECTIVE: To describe the development of 3D-printed sinus and skull base models for use in endoscopic skull base surgery. DESIGN, SETTING, AND PARTICIPANTS: In this single-center study performed from April 1, 2017, through June 1, 2017, a total of 7 otolaryngology residents and 2 attending physicians at a tertiary academic center were recruited to evaluate the procedural anatomical accuracy and haptic feedback of the printed model. INTERVENTIONS: A 3D model of sinus and skull base anatomy with high-resolution, 3D printed material (VeroWhite) was printed using a 3D printer. Anatomical accuracy was assessed by comparing a computed tomogram of the original patient with that of the 3D model across set anatomical landmarks (eg, depth of cribriform plate). Image-guided navigation was also used to evaluate accuracy of 13 surgical landmarks. Likert scale questionnaires (1 indicating strongly disagree; 2, disagree; 3, neutral; 4, agree; and 5, strongly agree) were administered to 9 study participants who each performed sinus and skull base dissections on the 3D-printed model to evaluate anatomical accuracy and haptic feedback. MAIN OUTCOMES AND MEASURES: Main outcomes of the study include objective anatomical accuracy through imaging and navigation and haptic evaluation by the study participants. RESULTS: Seven otolaryngology residents (3 postgraduate year [PGY]-5 residents, 2 PGY-4 residents, 1 PGY-3 resident, and 1 PGY-2 resident) and 2 attending physicians evaluated the haptic feedback of the 3D model. Computed tomographic comparison demonstrated a less than 5% difference between patient and 3D model measurements. Image-guided navigation confirmed accuracy of 13 landmarks to within 1 mm. Likert scores were a mean (SD) of 4.00 (0.71) for overall procedural anatomical accuracy and 4.67 (0.5) for haptic feedback. CONCLUSIONS AND RELEVANCE: This study shows that high-resolution, 3D-printed sinus and skull base models can be generated with anatomical and haptic accuracy. This technology has the potential to be useful in surgical training and preoperative planning and as a supplemental or alternative simulation or training platform to cadaveric dissection.
引用
- Hsieh TY, Cervenka B, Dedhia R, et al. Assessment of a Patient-Specific, 3-Dimensionally Printed Endoscopic Sinus and Skull Base Surgical Model. JAMA Otolaryngol Head Neck Surg. 2018. PMID: 29799965. doi:10.1001/jamaoto.2018.0473
供执业医师工作参考,不替代临床判断;数值与分级以指南原文为准。