文献速递耳科与耳神经小儿耳鼻咽喉

术中患者特异性3D打印颞骨模型对人工耳蜗植入术者认知负荷的影响:一项随机对照试验

Impact of Intraoperative Patient-Specific 3D-Printed Temporal Bones: A Randomized Controlled Trial.
PubMed 文献 · Laryngoscope · 2026-09-01

这项随机对照试验纳入40例连续成人初次人工耳蜗植入手术,由7名主治医师和5名培训医师完成,1:1随机分为标准影像规划组和加用术中3D打印颞骨模型检查组。主要结局用Surg-TLX测量术中认知负荷。结果显示主治医师使用模型后总体认知负荷降低(3.8 vs 5.5,p<0.01),住院医师反而升高(7.2 vs 4.8,p=0.02),专科培训医师无显著差异。

要点

  • 主治医师术中查看3D打印颞骨模型可降低总体认知负荷。
  • 住院医师使用模型后总体负荷及精神、体力疲劳反而增加。
  • 模型被认为准确有用,尤其利于培训医师预判手术难度和解剖边界。

核心结论

  • 术中3D打印颞骨模型对人工耳蜗植入术者认知负荷的影响受手术经验调节:主治医师可借此实现认知卸载,培训医师则被激发更多心理努力。
  • 建议选择性实施,使模型使用与术者经验水平相匹配,以促进手术效率和培训。

研究设计与样本

  • 随机对照试验,纳入40例连续成人初次人工耳蜗植入手术。
  • 由7名主治医师和5名培训医师完成,1:1随机分为标准影像规划组和加用术中3D打印颞骨模型检查组。
  • 主要结局为术中认知负荷,用Surg-TLX测量并以线性混合效应模型分析。
  • 次要结局包括模型解剖、效用和用户体验评分(Schlegel问卷)及术中挑战预测。

主要发现

  • 主治医师使用3D模型组总体认知负荷低于对照组(3.8 vs 5.5,p<0.01),主要因体力疲劳降低(p=0.01)。
  • 住院医师使用模型组总体负荷高于对照组(7.2 vs 4.8,p=0.02),精神疲劳(p=0.01)和体力疲劳(p<0.001)均增加。
  • 专科培训医师总体负荷无显著差异(8.2 vs 8.0,p=0.88),但病例复杂度评分降低(p=0.02),体力疲劳升高(p=0.04)。
  • 模型被认为准确且有用,尤其用于培训医师教育、预判病例难度和解剖边界。

关键数值与推荐

  • 主治医师总体认知负荷3.8 vs 5.5(p<0.01)。
  • 住院医师总体认知负荷7.2 vs 4.8(p=0.02)。
  • 专科培训医师总体认知负荷8.2 vs 8.0(p=0.88)。
  • 证据等级为Level II。

临床怎么用

  • 主治医师可在人工耳蜗植入术中参考患者特异性3D打印颞骨模型以降低认知负荷。
  • 对住院医师等培训医师使用模型需注意可能增加其精神和体力疲劳。
  • 可根据术者经验水平选择性使用3D打印模型,兼顾手术效率与培训需求。

以上解读依据论文摘要(全文未开放获取或许可不允许翻译转载)。

原文

OBJECTIVE: To determine if intraoperative inspection of patient-specific 3D-printed TB models, as a supplement to standard imaging, affects the cognitive load of surgeons during cochlear implantation (CI). METHODS: This randomized controlled trial included 40 consecutive adult primary CI surgeries performed by seven attending and five trainee surgeons at a large CI center. Cases were randomized 1:1 to current standard with surgical planning based on imaging review (controls) or to current standard plus intra-operative inspection of a 3D-printed model (intervention). The primary outcome, intraoperative cognitive load, was measured using the Surgery Task Load Index (Surg-TLX) and analyzed with linear mixed-effects models. Secondary outcomes included ratings of model anatomy, utility, and user experience (Schlegel-questionnaire) and prediction of intraoperative challenges. RESULTS: Attending surgeons experienced lower overall cognitive load using 3D models versus controls (3.8 vs. 5.5; p < 0.01), driven by reduced physical fatigue (p = 0.01). Conversely, residents reported higher overall load (7.2 vs. 4.8; p = 0.02) with increased mental (p = 0.01) and physical fatigue (p < 0.001). Fellows showed no significant difference in overall load (8.2 vs. 8.0; p = 0.88) but noted lower case complexity (p = 0.02) offset by higher physical fatigue (p = 0.04). Models were viewed as accurate and useful, particularly for trainee education, anticipating case difficulty and anatomical boundaries. CONCLUSION: The clinical impact of intraoperative 3D-printed models during CI is modulated by surgical experience. For attendings, models act as high-fidelity references facilitating cognitive offloading, whereas they stimulate mental effort for trainees. Selective implementation is recommended to align use of models to surgical experience level to promote operative efficiency and surgical training. LEVEL OF EVIDENCE: Level II.

来源:Laryngoscope,查看原文。版权归原作者所有。

引用

  1. Omari A, Nwosu OI, Andersen SAW, et al. Impact of Intraoperative Patient-Specific 3D-Printed Temporal Bones: A Randomized Controlled Trial. Laryngoscope. 2026. PMID: 42680684. doi:10.1002/lary.70887

供执业医师工作参考,不替代临床判断;数值与分级以指南原文为准。