文献速递口腔修复与种植

不同牙种植钻孔导板设计对截骨热生成影响的体外研究

Effect of different dental implant drilling template designs on heat generation during osteotomy - an in vitro study.
PubMed 文献 · Clin Oral Implants Res · 2021-10-27

本体外研究比较五种种植钻孔导板设计与对照组在截骨过程中的温度变化和冷却液分布。使用牛肋模型,在800 rpm、2 kg负载下记录3、6、9 mm深度温度,并测量冲洗液通过钻孔通道的流量。结果显示全引导导板减少截骨处冷却液量,导板设计影响有效冷却液体积,但未显著增加骨内温度。

要点

  • 全引导钻孔导板减少截骨处冷却液量,但未显著增加骨内温度。
  • 导板设计影响有效冷却液体积,侧开口设计冲洗量较高。
  • 6 mm深度温度升高最明显,2.2 mm钻针升温显著高于2.8 mm钻针。

核心结论

  • 在体外牛肋模型中,全引导钻孔导板减少截骨处冷却液量,导板设计影响有效冷却液体积,但未显著增加骨内温度。

研究设计与样本

  • 体外研究,比较五种导板设计(咬合夹板设计、咬合夹板覆盖、咬合夹板侧开口、杆设计、定向导板)与对照组及阴性对照组,在牛肋模型中以800 rpm、2 kg负载进行先锋钻和一枚后续钻,热电偶记录3、6、9 mm深度温度变化,并测量冲洗液通过钻孔通道的流量。

主要发现

  • 平均温度升高(°C):对照组4.9,阴性对照组12,咬合夹板设计5.6,咬合夹板覆盖4.7,咬合夹板侧开口3.8,杆设计5.1,定向导板4.9。
  • 最高温度升高出现在钻孔深度6 mm(p < .006)。
  • 2.2 mm钻针的温度升高显著高于2.8 mm钻针(p < .001)。
  • 冲洗液通过钻孔通道的平均流量(ml/min):对照组28.5,咬合夹板设计4.1,咬合夹板覆盖2,咬合夹板侧开口5.8,杆设计4,定向导板24.1。

临床怎么用

  • 临床使用全引导钻孔导板时需关注冷却液到达截骨处的有效量,可优先考虑侧开口等设计以改善冲洗液分布。

局限性

  • 本研究为体外牛肋模型实验,结论需结合临床进一步验证。

以上解读依据论文摘要(全文未开放获取或许可不允许翻译转载)。

原文

OBJECTIVES: This in vitro study examined the effect of different implant drilling template designs on heat generation during osteotomy and on cooling fluid distribution. MATERIAL AND METHODS: Five different template designs were investigated in a standardized setup against a control group and a negative control group: Occlusal-splint-design (OSD), OSD-covering, OSD-lateral opening, Bar design, and Orientation template. Pilot and one consecutive drill were run at 800 rpm with external irrigation and 2-kg load. Thermocouples recorded temperature changes at depths of 3, 6, and 9 mm in a bovine rib model. In the second experimental setup, the drill channel of one rib sample was perforated, and the irrigation volume passing through the drill channel was collected separately over time. RESULTS: Following mean temperature rises occurred [in °C]: control, 4.9; negative control, 12; OSD, 5.6; OSD-covering, 4.7; OSD-lateral opening, 3.8; Bar design, 5.1; and Orientation template, 4.9. The highest temperature increases were found at a drilling depth of 6 mm (p < .006). The 2.2-mm drill resulted in a significantly higher temperature rise than the 2.8-mm drill (p < .001). The mean volume (ml/min) of irrigation through the drill channel was Control group-flow, 28.5; OSD, 4.1; OSD-covering, 2; OSD-lateral opening; 5.8; bar design, 4; and Orientation template, 24.1. CONCLUSION: Within the limitations, it was shown that fully guided drilling templates reduce the amount of cooling liquid at the point of osteotomy. The template design had an influence on the effective volume of the cooling liquid. However, this did not seem to increase the intraosseous temperature significantly.

来源:Clin Oral Implants Res,查看原文。版权归原作者所有。

引用

  1. Waltenberger L, Wied S, Wolfart S, et al. Effect of different dental implant drilling template designs on heat generation during osteotomy - an in vitro study. Clin Oral Implants Res. 2021. PMID: 34587303. doi:10.1111/clr.13864

供执业医师工作参考,不替代临床判断;数值与分级以指南原文为准。