文献速递牙体牙髓病

三种镍钛疏通锉的设计、冶金、显微硬度与力学性能多方法评估

Evaluation of Design, Metallurgy, Microhardness, and Mechanical Properties of Glide Path Instruments: A Multimethod Approach.
PubMed 文献 · J Endod · 2021-09-16

本研究比较ProGlider、Edge Glide Path和R-Pilot三种镍钛疏通锉的设计、冶金、显微硬度和力学性能。每组44支,采用立体显微镜、扫描电镜、能谱分析、差示扫描量热法及扭转、弯曲、屈曲测试。结果显示R-Pilot显微硬度、最大扭转和屈曲载荷最高,ProGlider最柔韧,Edge Glide Path旋转角度最大。

要点

  • R-Pilot显微硬度、最大扭转和屈曲载荷最高。
  • ProGlider柔韧性最优(144.1 gf)。
  • Edge Glide Path旋转角度最大(683.5°)。

核心结论

  • 器械设计差异和相变温度决定了其力学行为。
  • R-Pilot扭矩、屈曲载荷和显微硬度最高,ProGlider最柔韧。

研究设计与样本

  • 共选取132支镍钛疏通锉,ProGlider、Edge Glide Path和R-Pilot各44支。
  • 采用立体显微镜和扫描电镜评估设计,能谱分析测镍钛比,差示扫描量热法测相变温度。
  • 进行显微硬度及扭转、弯曲和屈曲抗力测试,统计采用Mood中位数检验,显著性水平5%。

主要发现

  • Edge Glide Path blade数量最少,R-Pilot螺旋角最大。
  • 所有器械镍钛比接近等原子比,但横截面和尖端几何不同。
  • Edge Glide Path表面光洁度更光滑。
  • R-Pilot室温下呈马氏体特性,其他器械为奥氏体加R相混合。
  • R-Pilot显微硬度436.8 HV、最大扭转0.9 Ncm、屈曲载荷0.7 N最高(P < .05)。

临床怎么用

  • 根据临床需要选择器械:需高扭矩和抗屈曲时可选R-Pilot,需柔韧性时可选ProGlider。

以上解读依据论文摘要(全文未开放获取或许可不允许翻译转载)。

原文

INTRODUCTION: This study aims to compare the design, metallurgy, microhardness, and mechanical properties of 3 glide path nickel-titanium (NiTi) instruments. METHODS: A total of 132 ProGlider (Dentsply Sirona, Ballaigues, Switzerland), Edge Glide Path (EdgeEndo, Johnson City, TN), and R-Pilot instruments (VDW, Munich, Germany) (44 per group) were selected. Design was assessed through stereomicroscopy (blades, helical angle, measuring lines, and deformation) and scanning electron microscopy (symmetry, cross section, tip, and surface finishing). NiTi ratios were measured by energy-dispersive X-ray spectroscopy and phase transformation temperatures by differential scanning calorimetry. Microhardness and mechanical performance (torsion, bending, and buckling resistance tests) were also evaluated. Statistical analyses were performed with the Mood median test with a significance set at 5%. RESULTS: The Edge Glide Path had the lowest number of blades and the R-Pilot the greatest helical angle. All instruments had an almost equiatomic NiTi ratio, while showing different cross sections and tip geometries. The Edge Glide Path had a smoother surface finishing. The R-Pilot showed martensitic characteristics at room temperature, whereas mixed austenite plus R-phase was observed in the other instruments. The R-Pilot had higher results on the microhardness (436.8 hardness Vickers number), maximum torsion (0.9 Ncm), and buckling load (0.7 N) tests (P < .05), whereas the Edge Glide Path had a superior angle of rotation (683.5°) and the ProGlider was more flexible (144.1 gf) (P < .05). CONCLUSIONS: Differences in the design of the instruments and the phase transformation temperatures accounted for their mechanical behavior. The R-Pilot showed the highest torque, buckling, and microhardness, whereas the ProGlider instrument was the most flexible.

来源:J Endod,查看原文。版权归原作者所有。

引用

  1. Martins JNR, Silva EJNL, Marques D, et al. Evaluation of Design, Metallurgy, Microhardness, and Mechanical Properties of Glide Path Instruments: A Multimethod Approach. J Endod. 2021. PMID: 34537227. doi:10.1016/j.joen.2021.09.003

供执业医师工作参考,不替代临床判断;数值与分级以指南原文为准。