文献速递口腔修复与种植

后牙单牙缺损定制软组织替代物的设计:一项体外概念验证研究

Design of customized soft-tissue substitutes for posterior single-tooth defects: A proof-of-concept in-vitro study.
PubMed 文献 · Clin Oral Implants Res · 2021-10-16

识别出三种形状:上颌方形(n=13)、上颌矩形(n=11)和下颌较小形状(n=9),最大厚度位于牙槽嵴上方颊侧(中位数2 mm),边缘最薄0.2 mm。研究建立了设计定制及平均形状STS的新方法。

要点

  • 上颌后牙缺损STS可分为方形和矩形两种形状。
  • 下颌后牙缺损STS平均形状较上颌小。
  • STS最厚处在牙槽嵴上方颊侧(中位数2 mm),边缘最薄0.2 mm。

核心结论

  • 研究建立了设计定制及平均形状软组织替代物的新方法,用于后牙单牙缺损的体积增量。

主要发现

  • 根据形状识别出三组STS:上颌方形(n=13),舌颊向长度10 mm,近远中向宽度7-10 mm。
  • 上颌矩形(n=11),长度11 mm,宽度4-7 mm。
  • 下颌平均形状(n=9)较小,长度6-8 mm,宽度5-10 mm。
  • 所有STS最厚处位于牙槽嵴上方颊侧,中位数2 mm;边缘最薄为0.2 mm。

临床怎么用

  • 未来具有适配几何形状的STS可能提高体积增量的效率和精确度,同时减少手术时间。

以上解读依据论文摘要(全文未开放获取或许可不允许翻译转载)。

原文

OBJECTIVES: Soft-tissue volume augmentation treatments do not provide the satisfactory long-term functional and esthetic outcomes. The aim of the study was to develop a standardized digital procedure to design individual soft-tissue substitutes (STS) and apply mathematical modeling to obtain average shape STS for single posterior tooth defects. MATERIAL AND METHODS: Thirty-three casts from 30 patients were scanned. STS were designed with a computer-aided design software and a systematic procedure standardized the measurements across all STS using 3D-analysis software. The occlusal, mesial-distal, and buccal-lingual planes were defined to partition, each STS and produce a mesh. The thickness values of each 3D slice were documented in a coordinate system chart to generate a scatter graph. Graphs were embedded into images (Orange software) and images were analyzed via hierarchical clustering. RESULTS: Three STS groups were identified according to shape. Two shapes corresponded to the maxilla defects: a square (n = 13) with dimensions of 10 mm in a lingual-buccal (length) and 7-10 mm in a mesial-distal (width) direction; a rectangle (n = 11) of 11 mm in length and 4-7 mm in width. The average shape for mandible defects (n = 9) was smaller (6-8 mm in length, 5-10 mm in width). The highest thickness in all STS was in the buccal portion, above the alveolar ridge, with median values of 2 mm. The lowest thickness of 0.2 mm was at the edges. CONCLUSIONS: The study developed novel methodology to design customized, as well as average shape STS for volume augmentation. Future STS harboring adapted geometry might increase volume augmentation efficiency and accuracy, while reducing surgical time.

来源:Clin Oral Implants Res,查看原文。版权归原作者所有。

引用

  1. Sun Y, Yu T, Strasding M, et al. Design of customized soft-tissue substitutes for posterior single-tooth defects: A proof-of-concept in-vitro study. Clin Oral Implants Res. 2021. PMID: 34448240. doi:10.1111/clr.13831

供执业医师工作参考,不替代临床判断;数值与分级以指南原文为准。