文献速递牙体牙髓病

当代牙胶尖热行为与物理性能研究

The investigation of thermal behaviour and physical properties of several types of contemporary gutta-percha points.
PubMed 文献 · Int Endod J · 2021-09-06

该研究分析了六种品牌牙胶尖的组成、热导率及热行为。结果显示不同品牌牙胶尖的无机成分重量百分比存在显著差异(p < .05),PTG热导率最低(0.42 W/m K),无机成分百分比与热导率呈正相关(r = 0.95)。β→α相变温度在品牌间有显著差异(p < .05),而α→无定形态转变无显著差异(p > .05)。

要点

  • 不同品牌牙胶尖无机成分含量差异显著,影响其热导率。
  • PTG牙胶尖热导率最低(0.42 W/m K),无机成分与热导率正相关(r = 0.95)。
  • β→α相变温度因品牌而异,α→无定形态转变温度无显著差异。

核心结论

  • 不同品牌牙胶尖的化学组成和DSC初始相变温度存在差异。
  • 六种品牌中Conform Fit TM牙胶尖的无机成分百分比和热导率最低。
  • 热导率与无机成分百分比和锌含量呈最强正相关,与牙胶含量比例呈负相关。

研究设计与样本

  • 研究分析了六种品牌牙胶尖:PTG、PTU、Autofit、Mtwo、GC和ISO。
  • 采用定量化学分析分离有机和无机成分,激光闪射法检测热导率,DSC分析热行为。
  • 使用Kruskal-Wallis和Dunn检验比较组间化学组成和DSC温度,简单线性回归分析组成与热导率关联,p < .05为显著。

主要发现

  • 各组牙胶尖无机成分重量百分比存在显著差异(p < .05)。
  • PTG热导率最低(0.42 W/m K),无机成分百分比与热导率正相关(r = 0.95)。
  • β→α相变的初始相变温度和峰值温度组间有显著差异(p < .05),α→无定形态转变无显著差异(p > .05)。

临床怎么用

  • 选择牙胶尖时应考虑品牌间热行为差异对根管充填的影响。
  • 热导率与无机成分含量相关,可能影响热牙胶充填时的热传递效率。

以上解读依据论文摘要(全文未开放获取或许可不允许翻译转载)。

原文

AIM: To analyse the contents and thermal behaviour of several brands of contemporary gutta-percha points due to the variable nature of the components of gutta-percha, and the impact they can have on the physical properties of this unique material during canal filling. METHODOLOGY: Six brands of gutta-percha were investigated: Conform Fit TM Gutta-Percha Points for ProTaper Gold® (PTG) (Dentsply Sirona), ProTaper® Universal Gutta-Percha Points (PTU) (Dentsply Sirona), Autofit TM Feathered Tip Gutta Percha (Kerr), Mtwo® Gutta-Percha (VDW), Gutta Percha Root Canal Points (GC, GC Corporation) and Gutta-Percha Points ISO Color-Coded (ISO; Dentsply Sirona). The organic and inorganic fractions of gutta-percha points were separated by quantitative chemical analysis. Thermal conductivity was detected using a laser flash method. In addition, the thermal behaviour of gutta-percha in response to temperature variations was analysed using differential scanning calorimetry (DSC). Kruskal-Wallis and Dunn tests were applied for comparisons amongst groups for chemical compositions and temperature obtained from DSC. The associations between compositions and thermal conductivity were determined using simple linear regression. A p value <.05 was considered to be statistically significant. RESULTS: There were significant difference in the inorganic fractions of the gutta-percha points in percentage by weight amongst the groups (p < .05). PTG had the lowest thermal conductivity (0.42 W/m K). A positive correlation was observed between the percentage of inorganic fraction and thermal conductivity (r = 0.95). The initial phase changing temperature and peak temperature measured by DSC were significantly different when the β-form transformed to α-form (p < .05), whereas no significant difference was found during the α-form to the amorphous-phase transition (p > .05). CONCLUSIONS: Chemical compositions and initial phase changing temperature by DSC varied according to the various brands of gutta-percha points. Conform Fit TM gutta-percha had the lowest percentage of inorganic fraction and thermal conductivity amongst these six brands of gutta-percha. Thermal conductivity had the strongest positive correlation with the percentage of inorganic components and zinc, whilst there was a negative correlation to the amount (ratio) of gutta-percha.

来源:Int Endod J,查看原文。版权归原作者所有。

引用

  1. Liao SC, Wang HH, Hsu YH, et al. The investigation of thermal behaviour and physical properties of several types of contemporary gutta-percha points. Int Endod J. 2021. PMID: 34420210. doi:10.1111/iej.13615

供执业医师工作参考,不替代临床判断;数值与分级以指南原文为准。