根管弯曲度与镍钛锉力学性能对扭矩生成的影响
本研究比较4种镍钛锉在4种弯曲角度人工根管中产生的扭矩。结果显示弯曲角度与锉系统类型存在显著相关性(P < .05),弯曲度增大时总扭矩和最大扭矩均增加;往复运动锉在15°和25°时扭矩高于连续旋转锉,ProTaper Next在35°和45°时扭矩最低(P < .05)。
要点
- 根管弯曲角度与镍钛锉系统类型对扭矩生成存在显著交互影响(P < .05)。
- 弯曲度增大时,各锉的总扭矩和最大扭矩均增加。
- 35°和45°高弯曲角度下ProTaper Next扭矩值最低(P < .05)。
核心结论
- 根管弯曲度、镍钛锉设计与热处理及运动方式均影响器械操作中产生的扭矩。
研究设计与样本
- 体外研究,选用4个品牌镍钛锉在含15°、25°、35°、45°四种弯曲角度人工根管的 tempered steel block 中测试。
- 每种锉按厂家说明在动态模型中使用,并在根管末端附加15次4 mm轴向上下运动,记录总扭矩和最大扭矩。
- 采用双因素方差分析和Duncan事后比较检验,显著性水平为95%。
主要发现
- 弯曲角度与锉系统类型之间观察到显著相关性(P < .05)。
- 随着根管弯曲度增加,产生的总扭矩和最大扭矩均增加。
- 在15°和25°时,往复运动镍钛锉产生的总扭矩和最大扭矩高于连续旋转锉。
- 传统镍钛合金的ProTaper Universal随弯曲角度增加,总扭矩和最大扭矩增幅最陡。
- ProTaper Next在35°和45°较高根管角度下扭矩值最低(P < .05)。
临床怎么用
- 临床选择镍钛锉时应考虑根管弯曲角度及锉的运动方式对扭矩的影响。
局限性
- 原文提及存在研究局限性,但未具体说明。
以上解读依据论文摘要(全文未开放获取或许可不允许翻译转载)。
原文
INTRODUCTION: This study aimed to compare the torque generated by 4 different files in root canals with 4 different curvature angles. METHODS: Four brands of nickel-titanium (NiTi) endodontic files were selected: WaveOne Primary (Dentsply Sirona, Ballaigues, Switzerland), WaveOne Gold Primary (Dentsply Sirona), ProTaper Universal F2 (Dentsply Sirona), and ProTaper Next X2 (Dentsply Sirona). A tempered steel block containing artificial canals with 4 different canal curvatures (15°, 25°, 35°, and 45°) was constructed. Each file was used according to the manufacturer's instructions in the dynamic model, with an added 15 axial up-and-down movements of 4 mm at the end of the canal. The generated torque was recorded, and the total and maximum torque values were measured. Two-way analysis of variance and the Duncan post hoc comparison test were performed at a significance level of 95%. RESULTS: A significant correlation between the curvature angle and the type of file system was observed (P < .05). As the degree of canal curvature increased, the generated total and maximum torque increased. At 15° and 25°, the NiTi files with reciprocating motion generated a higher total and maximum torque than files with continuous rotation. ProTaper Universal of conventional NiTi alloy showed the steepest increase in the generated total and maximum torque with the increasing curvature angle. The ProTaper Next file had the lowest torque values at the higher canal angles of 35° and 45° (P < .05). CONCLUSIONS: Despite the study limitations, it can be concluded that root canal curvature, design, and heat treatment of NiTi files and file kinematics affect the generated torque during instrumentation.
引用
- Kwak SW, Ha JH, Shen Y, et al. Effects of Root Canal Curvature and Mechanical Properties of Nickel-Titanium Files on Torque Generation. J Endod. 2021. PMID: 34237386. doi:10.1016/j.joen.2021.06.019
供执业医师工作参考,不替代临床判断;数值与分级以指南原文为准。