数字化稳定咬合板系统的构建与初步临床评价
上海交通大学医学院附属第九人民医院口腔修复科于2019年4至5月招募2名健康志愿者,采用CAD/CAM数字化流程与常规流程各制作稳定咬合板,通过试戴清单进行临床初步评价。结果显示数字化咬合板系统具有临床可行性,两名受试者数字化咬合板临床初步评价总分分别为26和26,常规法分别为25和23。
要点
- 数字化稳定咬合板流程可行,包括模型扫描、下颌运动记录、CAD设计与3D打印。
- 2名受试者初步评价总分数字化法为26和26,常规法为25和23。
- 样本量小,仅为初步临床评价,需进一步验证。
核心结论
- 数字化稳定咬合板工作流程可行,临床初步评价总分优于常规法。
研究设计与样本
- 于2019年4至5月招募2名健康志愿者(1名25岁男性、1名24岁女性),每人均制作数字化法和常规法稳定咬合板各1个。
主要发现
- 数字化咬合板系统构建成功,临床初步评价两名受试者数字化法总分均为26,常规法分别为25和23。
临床怎么用
- 数字化稳定咬合板系统可作为稳定咬合板的制作选择,但需更多样本验证。
局限性
- 样本量仅2名健康志愿者,仅为初步临床评价,未报告统计检验。
以上解读依据论文摘要(全文未开放获取或许可不允许翻译转载)。
原文
To established a digital workflow for stabilization occlusal splint with computer-aided design and computer-aided manufacturing (CAD/CAM) methods. Two subjects were enrolled from April 2019 to May 2019 from Department of Prosthodontics, Ninth People's Hospital, Shanghai Jiao Tong University School of Medicine (one male, 25 years old; one female, 24 years old). The working models of the participants' dentition were made. Two stabilization occlusal splints were manufactured for each participant using digital workflow and conventional workflow. With the digital workflow, the three-dimensional (3D) scanning of the cast, recording of the digital personalized mandibular movements and condyle trajectory, and the design and the 3D printing for the fabrication of the final appliance using CAD/CAM technologies were performed. With conventional workflow, conventional technologies were adopted based on requirements and experiment of designing and manufacturing of stabilization splint. During try-in, a checklist was built to compare the clinical performance of the two workflows. The digital workflow of the stabilization occlusal splint was built successfully. The total score of clinical primary evaluation by the two subjects were 26 and 26 for digital workflow splints, and 25 and 23 for conventional workflow splints. Digital stabilization occlusal splint workflow is feasible. 为构建数字化咬合板系统,上海交通大学医学院附属第九人民医院口腔修复科于2019年4至5月招募2名健康志愿者(1名25岁男性和1名24岁女性),用硅橡胶取模灌制石膏模型,每位受试者均采用数字化法和常规法制作咬合板:用口腔三维扫描仪扫描石膏模型,建立数字化模型,借助下颌运动分析系统记录颌位关系及下颌运动参数,进行计算机辅助设计并三维打印制作咬合板;以常规法设计制作的咬合板为对照,对两种咬合板进行临床评价。结果显示数字化咬合板系统具有临床可行性。临床初步评价显示,数字化咬合板客观评价与主观评分总分优于传统咬合板。.
引用
- Lin R, Yu CH, Sun J, et al. [Construction and preliminary clinical evaluation of digital stabilization occlusal splint system]. Zhonghua Kou Qiang Yi Xue Za Zhi. 2020. PMID: 33280364. doi:10.3760/cma.j.cn112144-20200629-00381
供执业医师工作参考,不替代临床判断;数值与分级以指南原文为准。