文献速递牙体牙髓病口腔正畸口腔颌面外科

三维打印导板辅助融合牙半切与自体移植一例

Use of 3-dimensional-Printed Guide in Hemisection and Autotransplantation of a Fusion Tooth: A Case Report.
PubMed 文献 · J Endod · 2021-01-17

本文报告一名10岁患者上颌右侧侧切牙与多生牙融合,因经济限制未采用多学科联合方案。使用三维打印导板行半切术并拔除多生牙,随后将患牙自体移植至美学和咬合更佳位置,三维打印牙模型用于预备受区。术后6个月诊断牙髓坏死及无症状性根尖周炎,完成根管治疗后8个月骨愈合,14个月无临床症状且患者满意,间隙自行关闭。

要点

  • 三维打印导板可辅助融合牙的半切与自体移植手术。
  • 术后需监测牙髓活力,本例6个月出现牙髓坏死并完成根管治疗。
  • 自体移植后14个月临床成功,间隙无需正畸自行关闭。

核心结论

  • 对于因发育阶段或社会经济原因不接受其他方案的年轻融合牙患者,三维打印导板辅助半切联合自体移植可作为替代选择。

研究设计与样本

  • 本文为个案报告,对象为1名10岁患者,上颌右侧侧切牙与多生牙融合。

主要发现

  • 术后6个月患牙诊断牙髓坏死及无症状性根尖周炎,完成根管治疗后8个月观察到骨愈合。
  • 半切与移植后14个月患者无临床症状且对结果满意,牙#7与#8间隙无需正畸治疗自行关闭。

临床怎么用

  • 现代牙髓病技术如锥形束CT成像和三维打印在有益于患者时应被采用。

局限性

  • 本文为单个病例报告,结论外推需谨慎。

以上解读依据论文摘要(全文未开放获取或许可不允许翻译转载)。

原文

Three-dimensional (3D)-printed guides have been used in endodontics to prepare a conservative access, locate calcified or missing canals, and perform precisive osteotomy in apicoectomy. Here, we present the treatment of a fusion tooth by combining 3D printing technology and endodontic intervention in a 10-year-old patient. The bifid crown of a maxillary right lateral incisor #7 had caused esthetic concerns and malocclusion. Clinical and radiographic examinations showed that #7 is fused with a supernumerary tooth with 2 independent root canals. The fusion involved the entire crown and the coronal and middle roots. Because of financial constraints, a multidisciplinary approach involving endodontic, orthodontic, and prosthodontic treatment was excluded. We hemisectioned the tooth intraorally with a 3D-printed guide, extracted the supernumerary tooth, and transplanted tooth #7 to a position with improved esthetics and occlusion. A 3D-printed tooth replica was used to prepare the recipient site for autotransplantation. At the 6-month follow-up, tooth #7 was diagnosed with pulp necrosis and asymptomatic apical periodontitis. Root canal treatment of tooth #7 was completed, and osseous healing was observed 8 months later. The patient had no clinical symptoms and was satisfied with the outcome 14 months after hemisection and transplantation. The open space between teeth #7 and #8 was closed without orthodontic treatment. We present an alternative option to treat a fusion tooth in young patients who do not opt for other treatment options because of their stage of development or for socio-economic reasons. Techniques in modern endodontics, such as cone-beam computed tomographic imaging and 3D printing, should be adapted when it is beneficial to patients.

来源:J Endod,查看原文。版权归原作者所有。

引用

  1. Sato M, Garcia-Sanchez A, Sanchez S, et al. Use of 3-dimensional-Printed Guide in Hemisection and Autotransplantation of a Fusion Tooth: A Case Report. J Endod. 2021. PMID: 33352149. doi:10.1016/j.joen.2020.12.006

供执业医师工作参考,不替代临床判断;数值与分级以指南原文为准。